Q10: A given periodic signal (in volts), f(t) = 4 sin 8xt +2 cos 12nt Volts developed across Oresistor. (a) Determine the highest fundamental frequency possible for the signal. (b) Sketch two-sided amplitude and phase spectrum of f(t). (c) Find the total mean (average) power in f(t). (d) Calculate the percentage of the total mean power contained in each harmonic up to the fifth harmonic using the fundamental of the part (a).

Q10: A given periodic signal (in volts), f(t) = 4 sin 8xt +2 cos 12nt Volts developed across Oresistor. (a) Determine the highest fundamental frequency possible for the signal. (b) Sketch two-sided amplitude and phase spectrum of f(t). (c) Find the total mean (average) power in f(t). (d) Calculate the percentage of the total mean power contained in each harmonic up to the fifth harmonic using the fundamental of the part (a).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A frequency modulated signal is generated by modulating the carrier signal c(t) = 40 cos(2pi fc t),with fc = 106 MHz.The phase function of the FM modulated signal is known to be phase(t) = 10 sin(12,000pi t).Determine1. the average transmitted power of the FM modulated signal u(t),2. the peak-phase deviation,3. the peak-frequency deviation,4. the bandwidth of the FM modulated signal.
A superheterodyne receiver is to tune the range 88.1MHz to 107.1MHz. The RF circuit inductance is 1μH. Low-side injection is used.a. Calculate the minimum capacitance of the variable capacitor in the RF circuitb. Calculate the RF circuit capacitance tuning ratio c. If the receiver has a single converter stage and IF of 800kHz, calculate the capacitance tuning ratio of the local oscillator d. If the maximum capacitance of the variable capacitor of the local oscillator is 0.2pF, calculate the minimum capacitance e. If the receiver has a single converter stage and IF of 800kHz, calculate the image frequency of 103.7MHzf. Calculate the IFRR (in dB) of (e) if Q of the preselector is 50 g. To increase the IFRR of (e) to 40dB, double conversion is used. What must be the frequency of the 1st IF?
The equation of an angle-modulated voltage is v = 10 sin (l08t + 3 sin 104,). What form of angle modulation is this? Calculate the carrier and modulating frequencies, the modulation index and deviation, and the power dissipated in a 100-ohm resistor.
Q8/ If an information signal m( t ) = cos(2π100t) +10cos(2π1000t) . Write the formula of the frequency modulation ( FM ) when Ac =10 , Fc=10 ^ 6 Hz, Kf = π1000
An FM signal, eFM = 50 sin [2π(800k)t - 4 sin 2π(5k)t] is produced by a frequency modulator with -500Hz/V frequency deviation constant. Determine (a)Determine the equation of the carrier signal (b) What is the equation of the modulating signal (c) Determine the approximate bandwidth of the FM signal (use Carson’s Approximation)
A sinusoidal modulating waveform of amplitude 5v and a frequency of 2KHZ is applied to FM generator, which has a frequency sensitivity of 40Hz/Volt. Evalulate: Frequency deviation, modulation index, Bandwidth
1. An impedance coil takes 144 watts at a lagging power factor of 0.6. What value of capacitanceand resistance should be connected in series with the coil if the power input to the latter is toremain unchanged and the overall power factor is to be unity (in resonance)? The circuit isenergized by a 120 volt, 60 cps source.2. A series RLC circuit has a Q of 75 and a pass band between half-power frequencies of 160 cps.Calculate the frequency of resonance and upper and lower frequencies of the pass band.3. An impedance coil having a resistance of 30 ohms and a 50 cps inductive reactance of 33.3 ohmsis connected to a 125 volt 60 cps source. A series circuit consisting of a 20 ohm resistor and avariable capacitor is then connected in parallel with the coil. (a) for what values of capacitancewill the circuit be in resonance? (b) calculate the two values of line current for the condition ofresonance.4. A parallel-series filter like that of Fig. 13.10b in the scanned copy of the on page 364 is…
Q2 (B) Given m(t) = sin 2000 πt, kf = 200,000π, and kp = 8000 π.Find frequency deviation, Δf, for(i) Frequency Modulated (FM) signal(ii) Phase Modulated (PM) signal.
Consider a FM signal given by equation VFM (t) = 5 Cos [2x108 πt + 3 sin (40000πt)]. Calculate carrier frequency, modulating frequency, frequency deviation and bandwidth
A 8-stage impulse voltage generator is connected to a test object of load capacitance of 5000pF with wave front resistance equal to 700 Ω. If the wave tail and wave front times of the impulse wave are 50 μs and 1500 ns respectively. Calculate (i) wave tail resistance value and (ii) the capacitance of the impulse generator?
Since k = 0.35x10-3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 8.7 kΩ in the circuit in the figure In which option is the amplitude value (Vout) of the output voltage given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency. Since k = 0.35x10-3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 8.7 kΩ in the circuit in the figure In which option is the amplitude value (Vout) of the output voltage given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency.
Consider the modulating signal m(t) = 10 sin(2π10^10) that is used to modulate a carrier frequency of 25MHz