Q10/   choose the correct answer Non contact type temperature sensors are operating under the principle of conduction. Select one: True False

Q: Electronic balances must be ideally located in a room with continuous ventilation and natural flow…

A: This problem is from electronic balance.  The statement is true.

Q: he purpose of an adjustable pressure device

A: pressure devices is in the form of switch that operates an electrical contact when a certain set…

Q: what are three safety items to consider when using a voltage tester on energized circuits

A: Measuring live voltage in energized circuit can cause severe hazard to equipment and users if…

Q: What are the differences between pressure sensor, pressure gauge and pressure transmitter?  Explain…

A: Pressure sensor : It is a device that measure the pressure of gas or liquid. Generally pressure…

Q: .is required to stabilize an absolutely unstable system to achieve a specified performance.

A: if the system are unstable the desire performance can not be achieved. so it is required to…

Q: Identify and explain the safety procedures and precautions that should be followed when working with…

A: In this question , we will explain the safety precautions that should be followed when working with…

Q: An electric fuse consist of a small strip of wire with a low melting temperature. The current in the…

A: Given  2 fuses with current  I1 = 10 A & I2 = 20 A

Q: make a detailed report on the type of sensors use in measuring air quality INSIDE A ROOM

A: Type of sensors use in measuring air quality INSIDE A ROOM: IAQ sensor called Indoor Air Quality…

Q: What should be the K range for the following system to be stable?

A: The solution can be achieved as follows.

Q: Among the main causes of electrical failure involves Electro-Static-Discharge (ESD). Please…

A: Since there are 4 different questions (a), (b), (c) and (d), as per the guidelines, in the following…

Q: Explain how to do a continuity check on an electrical appliance plug. Explain how to test for…

A: Continuity test is performed to analyze where the flow of the electric current is continuous on not,…

Q: What is RG rating of coaxial cable. Please give me detailed information. Don't copy previously given…

A:

Q: Explain with a neat block diagram the measurement of temperature using Thermistor (measuring…

A: Thermistor is a resistor, which is a special variant(type). When temperature changes, then the…

Q: Health and safety is important at every stage of producing a PCB. For each of the equipment listed…

A: For designing PCB it is very important to follow safety precautions.

Q: Q.3 For Resistance temperature detectors (RTDS) I) What's the principle of operation for Resistance…

A:

Q: Mention the different parts of the Solar evacuated tubes used for heating purposes

A:

Q: Name two nationally recognised electrical testing laboratories in the United States.

A: In the following section, two nationally recognized electrical testing laboratories present in the…

Q: 17. What device is designed to open and disconnect a circuit in the event of excessive current?…

A: Fuse is the device which is used to open and disconnect a circuit in excessive current and it allows…

Q: Can a round 4 in. x 1/2 in. box marked as 8 cu in. with cable clamps supplied with 14/2 W/G NM cable…

A: Given data: Can a round 4 in. x 1/2 in. box marked as 8 cu in. with cable clamps supplied with 14/2…

Q: (b) Describe the role of IO devices with proper diagram.

A: 3. b) Input devices: These are the devices that collects the outer data and fed to the computer or…

Q: identify the different components of the ICEs fuel supply system.

A: Different energy sources are required in day to day life. These energy sources can be renewable or…

Q: What are the incubator parts

A: Incubator - An incubator is used to provide safe and controlled space for infants to live while…

Q: The amount of voltage required to start conduction in a gas is called what?

A: Here the discussion is about breakdown phenomenon in gaseous medium.

Q: Assuming all terminals are rated 75 degrees C, what is the maximum size overcurrent protective…

A: From the NEC table 310.15(B)16, the following table is obtained: Size AWG or kcmil Temperature…

Q: A flow chart detailing the sequence of manufacture of the energy saving switch for a kettle.

A: Since you have asked multiple question ,we will slove the first question for you .If you want any…

Q: Explain the operation of squelch circuit

A:

Q: 4. When is it necessary to switch the multimeter/voltmeter ranges in measuring voltage?

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: Explain Coordination between fuses and over current protective devices.

A: Overcurrent is current that excels the ampere rating of conductors, devices, or equipment under the…

Q: Draw the block diagram of a Temperature measurement system .Also identify the names of the…

A: Temperature Measurement System - The temperature measurement system is a device that is used to…

Q: What procedures and precautions would you expect to be taken by the staff to limit the overall…

A: In this case, the procedures and precautions that the staff should use to limit the overall…

Q: Identify three common simple electrical gadgets/devices at home after which: 1. propose a…

A: Nowadays, With the evolution of very compact power electronics devices and controllers, we are…

Q: Define energized in the context of exposure and describe the appropriate measure for hazard…

A: Energized system is a system when it is connected to a live voltage or current source. Transmission…

Q: Task: Add another potentiometer with voltage divider to control another diode led manually.…

A:

Q: A 600 V, 200 amp, class H fuse will fit into the same fuse holder as a 600 V 225 amp class H fuse…

A: Given A 600 V, 200 amp, class H fuse will fit into the same fuse holder as a 600 V 225 amp class H…

Q: Non contact type temperature sensors are operating under the principle of conduction. Select one: O…

A: Conduction is the principle of heat transfer which can be used for temperature measurement.…

Q: A cylindrical 00 AWG copper wire is coated with NEMA class B insulation. The normal operating…

A:

Q: Explain how Electrical Testing can be useful in identification of defects of electrical equipment or…

A:

Q: Discuss the moving iron voltmeter and ammeter?

A:

Q: 7. An attachment plug establishes connection between ____.

A: An attachment plug is electrical device.it is used to make connection by inserting in receptacle.

Q: what are the advantage and disadvantage of the sensors that are used in the labs

A:

Q: Explain with a neat block diagram the measurement of temperature using Thermistor (measuring…

A: Thermistor is a temperature dependent resistance. Thermistors are generally made up of metallic…

Q: Q1: Choose the correct answer: 1- Present-day applications of measuring instruments can be…

A: As per bartleby expert policy, only one individual question is to be answered. Kindly repost…

Q: 6. Explain the functioning of a thermocouple voltmeter and explain, where and why is this used and…

A: Thermocouple voltmeter

Q: QUESTION: Briefly describe the care and routine maintenance that would be necessary with a bank of…

A: Battery sulfation is the key issue behind the breakdown and losing capacity of lead batteries. To…

Q: Explain with a neat block diagram the measurement of temperature using Thermistor (measuring system)

A: The measurement of temperature using Thermistor is as follows:

Thermocouple

A thermocouple is a temperature measurement device. It includes diverse metal wires which are joined collectively to form a joint. At the same time as the junction is hot or cold, a small voltage is generated inside the measuring thermocouple electrical circuit, which corresponds to the temperature.