Q12 A refrigerator is used to remove a heat from a food at a rate of 532.6 kW and required a compressor power of 219 kW, what is the heat added to the surrounding (kW)? (D) 563.7 (B) 313.6 (A) 243.2 (C) 751.6 (E) None of them

Q12 A refrigerator is used to remove a heat from a food at a rate of 532.6 kW and required a compressor power of 219 kW, what is the heat added to the surrounding (kW)? (D) 563.7 (B) 313.6 (A) 243.2 (C) 751.6 (E) None of them

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 12RQ: Refrigerators currently being manufactured in the United States are using______as their refrigerant.

See similar textbooks

Related questions

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

Q: s): The butt connection shown below is fastened by 20-mm diameter bolts. Find the maximum allowable…

A: given; diameter (d)=20mmload(P)=?bearing stress(σb)=160MPatensile stess(σt)=80MPashearing…

Q: Using your current knowledge and a few relevant searches from the internet, what are the current…

A: Mechanical Engineering:- The study, design, development, construction, and testing of mechanical and…

Q: Water is discharged from reservoir (1) to reservoirs (2) * and (3) Knowing that Qv2 = 3/4 QV3 and…

Q: 4- The minimum force required to slide a body of weight W on a rough horizontal plane is A. W sing…

A: A force acting to slide a body on rough horizontal surface is shown below,

Q: Data: Hp2,3 = 2 m; A3 = 20 cm²; A₂ = 1 cm²; Hp0,1 = 0.8 m; NB= 74%(pump efficiency) To determine:…

Q: The motion of a particle is defined by the relation x = (at + b)³ where x and + are expressed in…

A: Given:Motion of the particle is defined by:x=(at+b)3 time, t=5.77 seca=3b=8

Q: While discussing fuel boiling in the fuel rail: Technician A says that fuel boiling in the fuel rail…

A: Write the value for lean and rich air fuel ratio: AF<14.7 Rich air-fuel ratioAF>14.7…

Q: . The wall of a cold room consists of a layer of cork sandwiched between the outer and inner walls…

Q: Glycerin at 10°C is flowing steadily through a 8-cm diameter pipe at 0.1 kg/s. What is the average…

A: Write the given data. m˙=0.1 kg/sD=0.08 m

Q: d) An acre is an area that covers 4047 m². In the U.S., a commonly used unit of volume is the…

Q: Determine the magnitude of the smallest force F3 so that the resultant force of all three forces has…

Q: In air pipline, the flow has the following conditions at section 1: 25C. 1.8 bar, 15 m/s velocity,…

Q: has an area of 5.5 ft² of 5 mm. If one side is at a temperature of 45° F and the other is at 23° F,…

Q: 3- Concurrent forces are those forces whose lines of action A. lie on the same line B. meet at one…

A: If all the forces acting in the same plane, then they are known as coplanar forces.

Q: 3. A star has a surface temperature of 5,500K. Determine the radiative heat transfer received by…

A: Given: Ts1=5500 KR=2100 kmTs2=300 Kα=0.8

Q: A calculator company produces a scientific calculator and a graphing calculator. Long term…

A: Given: Minimum demand of the scientific calculator each day=100 And minimum demand of the graphical…

Q: 6-16C A constant-velocity horizontal water jet from a stationary nozzle impinges normally on a…

A: Given date:- 1 constant velocity horizontal water jet 2 vertical flat plate…

Q: What are the two main types of characterization of smart materials? Using as few words as possible,…

A: There are two main types of characterization of smart materials are given as under,

Q: Smooth Surface No Friction External Force mass Damper D 3 Spring k mass m₂

A: Given,

Q: Q6: Design a cast iron piston for a single acting four stroke engine for the following data: Maximum…

A: Given: Maximum gas pressure→P=5MPa Cylinder bore→D=100 mm=0.10 m So the area of…

Q: Do you expect a material's stiffness to increase or decrease if there is more than one deformation…

A: The stiffness of material if different for different type of loadings causing deformation in the…

Q: what factors play a vital role in maximizing the convection heat transfer coefficient ?

A: convection heat transfer coefficient of Heat and mass transfer

Q: : A beam carries the loading shown in Fig. 4. Determine, (a) the smallest allowable width b of the…

Q: B) Locate the centroid x and determine the moment of inertia about x-axes.

A: Given

Q: Q1. Water flowing through a pipe has a dynamic viscosity of 8.9 x 10-4 Pas and a density of 1000…

Q: (a) Determine the reactions at A and E if P = 420 N. The reactions are positive if to the right or…

Q: Direction: Solve the following problems neatly and systematically and include free body diagrams.…

Q: The mass center G of the 1350-kg rear-engine car is located as shown in the figure. Determine the…

Q: What is the Reynolds number and flow regime at the beginning and at the end of the pipe? If the…

A: It is given that Diameter of pipe (d)= 50 cm = 0.50 m length of pipe (L)= 10 m mass flow rate m.=…

Q: An industrial spherical oven has 2.8 m diameter. It is placed in a factory floor where the air…

A: Given: D = 2.8 m, Therefore R = 1.4 m Ta = 25 oC = 25 +273 = 298 K Qpeak load = 905 kW Ts,…

Q: Determine the reactions at the supports:

A: To determine, the reactions at the supports The free body diagram of the given loadings is

Q: spring is k, and the spring is unstretched when = 90°. (a) Neglecting the weight of the rod, express…

Q: Problem 3 and no sign) produced by the applied forces about point C. Prepare an FBD to determine the…

Q: A Water Balloon Battle. You are launching water balloons at a rival team using a large slingshot.…

A: Given Data The height of the building is:h=30 ft=9.144 m The width of the building is:w=50 ft=15.24…

Q: A spherical ball with a diameter of 5 cm is suspended in the middle of a room with a temperature of…

Q: Q1-A/ Determine the moment of the force system shown in Figure (1A) with respect to moint A. 100 N…

A: Given: The load actin at the center, P = 100 N

Q: 1. How fast in rpm should the vessel be rotated about its own vertical axis so that 2/3 of its…

Q: n aircraft has the drag polar, C_d=0.015+0.05C_l^2 For a lift coefficient of 0.5, find the value of…

A: Given:Drag polar, Cd=0.015+0.05Cl2Lift coefficient, Cl=0.5

Q: What is one-dimensional kinematics and how does it work?

A: Kinematics is the analysis of positions and motions of objects as a function of time. This analysis…

Q: What is the specific gravity of a gas having a density of 5.88 kg/m3? Correct Answer: 4.80 ± 0.1

Q: While discussing fuel boiling in the fuel rail: Technician A says that fuel boiling in the fuel rail…

A: The condition for the lean and rich air fuel ratio: AF<14.7 Rich mixtureAF>14.7 Lean…

Q: Determine the magnitude of the resultant and vector B if R=A+B. B 35€ 8 in. - 5 in. (8.5 ir.. A = 35…

A: Given data: A=35 lbs Need to determine the magnitude of the resultant and vector B.

Q: Which physical property governs the operation of a bimetallic temperature element? Volumetric…

Q: Q4- For the shaded area shown in Figure (4), determine: a. The x coordinate of the centroid (x'). b.…

A: Given question: Q4. For the shaded area shown in figure, determine : a) The x coordinate of the…

Q: A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate…

Q: 2.1/2 Find the resultant of two forces hown in Figure and its direction with X axis sing Sine and…

A: Given:The forces are as:F1=350 kNF2=400 kNθ1=27°θ2=18°

Q: Weather radar provides information on the intensity as well as the total amount of precipitation.…

A: Given Data Reflective value at which the value need to calculate is: RV=47 dBZ The amount of time…

Q: Explain about availability in thermodynamics in detail.. like formulas and when it's applicable and…

Q: c) Find the stiffness of the spring for the mounting.

A: “Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Question

Q12 A refrigerator is used to remove a heat from a food at a rate of 532.6 kW and required a compressor
power of 219 kW, what is the heat added to the surrounding (kW)?
(D) 563.7
(A) 243.2
(B)
313.6
(C) 751.6
(E) None of them
far infore?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(II) A nuclear power plant operates at 65% of its maximumtheoretical (Carnot) efficiency between temperatures of 660°Cand 330°C. If the plant produces electric energy at the rateof 1.4 GW, how much exhaust heat is discharged per hour?
A certain heat engine operating on a Carnot cycle absorbs 150 J of heat per cycle at its hot reservoir at 135°C and has a thermal efficiency of 22.0%. (a) How much work does this engine do per cycle? (b) How much heat does the engine waste each cycle? (c) What is the temperature of the cold reservoir? (d) What mass of water could this engine pump per cycle from a well 35.0 m deep?
Provide complete solution and detailed diagram. A refrigerator is to remove heat from the cooled space at a rate of 300 KJ/min to maintain itstemperature at - 8oC. If the air surrounding the refrigerator is 25oC, determine the minimum powerrequired for this refrigerator? A. 0.263 kw B. 0.473 kw C. 0.623 kw D. 0.984 kw
A steam power plant develops a power output of 2840Kw. Te enthalpy of steam at the inlet if 2500 KJ/kg at500C and at the outlet is as follows: T=200C, dryness factor, x=0.8, hf2=561 KJ/kg and hfg2=1832 K/kg.Calculate the mass flow rate of the steam in kg/sec.
A fluid enters an apparatus at 480 ft/s, initially the pressureof the fluid is 120 psia, the specific volume of 5ft3/lb andthe internal energy is 383 BTU/lb. The fluid leaves theapparatus at 25psia, specific volume of 18 ft3/lb, an exitvelocity of 1200 ft/s and internal energy of 120 BTU/lb. Theheat radiation loss is 10 BTU/lb. Determine work steadyflow, WSF
Assume you purchase a new heat pump rated at 3 Refrigeration Tons [RT] and you estimate to use the heat pump for 13 hours per day [h/d] during the month of April (30 days), at a cost of $0.11 per kilowatt-hour [$/(kW h)]. What is the total cost, in dollars [$], to operate the heat pump in the month of April?
Show full detailed solution:A reversed Carnot engine removes 40,000 kW from a heat sink. The temperature of the heat sink is 260 K and the temperature of the heat reservoir is 320 K. Determine the power required of the engine Ans: 9230.7 kW
A “Carnot” refrigerator (the reverse of a Carnot engine)absorbs heat from the freezer compartment at a temperatureof –17°C and exhausts it into the room at 25°C. (a) Howmuch work would the refrigerator do to change 0.65 kg of waterat 25°C into ice at –17°C (b) If the compressor output is105 W and runs 25% of the time, how long will this take?
An engineer is proposing a refrigeration system. The refrigeration system is claimed to remove 595 Btu/min of heat from a space at 38 °F, reject the heat at 98 °F, and use 1.4 hp of power. Is this process possible?
Gaseous nitrogen actuates a Carnot power cycle in which the respective volumes at thefour corners of the cycle, starting at the beginning of the isothermal expansion, are V 1 =10.10, V 2 = 14.53, V 3 = 226.54, V 4 = 157.73 liter, what is the thermal efficiency of thecycle? k=1.399
Pls. answer thank you! In a 13 MW geothermal power plant, the mass flow of steam entering the turbine is 30 kg/s. The quality after throttling is 23% and enthalpy of ground water is 730 KJ/kg. Determine the overall efficiency of the plant.
5.4 In the continuous stirring heating tank, the flow rate of the influent is 200lb/min, the specific heat and density of the liquid are 0.32Btu/lbF, 62.4lb/ft^3, respectively, and the volume of the tank is 1.6ft^3, and the heat input Q from the heater is 2400Btu /min, the inflow temperature is kept constant at 90F. The inlet temperature suddenly dropped to 80F. In this case, find the response T(t) of the outflow temperature.