Q1(a). The open circuit voltage of a voltage amplifier is 12.5V when its input is connected to asignal source. Assume that the signal source voltage is 2.5V and its resistance is 2.0karespectively. If the input and output resistance of the amplifier is 5kn and 500 respectively,the amplifier output is connected to drive a load resistance 500n, determine the outputvoltage across the load.

Answered: Image /qna-images/answer/7ffbc536-4917-4f49-9cea-59f35ccde783.jpg

Answered: Q1(a). The open circuit voltage of a…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Suppose the ampliﬁer shown has |VOS|≤3 mV and R2 and R1 are 99 kΩ and 1.2 kΩ, respectively. What is the quiescent dc voltage at the ampliﬁer output?
Consider the operational amplifier circuit shown below. Assume the operational amplifier in the circuit is ideal. Determine the expression for the output signal, Vout, in terms of Vin,R1 and R2. Given the expression of the circuit [above’s output signal is Vout =3 − 0.5Vin, what is the maximum and minimum voltage that the input signal can have before the operational amplifier saturates.
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: 1- Determine the Q point, then illustrate it on the transistor I-V characteristic curves. 2- Is the transistor in the active region? Explain thoroughly. 3- Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. 4- Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. 5- Calculate the current gain, the input resistance, and the output resistance.
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. Calculate the current gain, the input resistance, and the output resistance.
We examined the common source amplifier shown in the figure in the 5th experiment. The capacitances have high enough value to assume them short circuit for the small-signal conditions. The gain of the amplifier for no-load condition is measured as 60. When a load resistance RL = 13 kΩ is connected, the gain is measured as 10. Calculate the output impedance of the amplifier, Rout.
Suppose we have a two-stage cascaded amplifier with an ideal transconductance amplifier as the first stage and an ideal transresistance amplifier as the second stage. What type of amplifier results and what is its gain in terms of the gains of the two stages? Repeat for the amplifiers cascaded in the opposite order.
Figure Q1(a) shows a Class A power amplifier circuit. Given the output signal is as shown in the figure, where Vm is the peak voltage and T is the period. For all transistors, you may neglect VBE and VCE(sat) in your calculations. (i) Derive an equation for power conversion efficiency, in terms of Vm, VCC, I and RL. Hence, deduce the maximum power conversion efficiency that is achievable. (ii) Determine the worst-case average power dissipation in each transistor under normal condition (i.e. RL is not open or short)
Show the manual solution of the simulated values for the given non-inverting amplifier below
On which criteria the power amplifiers are classified? What is the operating point of a class-A power amplifier? What is meant by efficiency? How much efficiency will be obtained in a class-A power amplifier? What are the applications of power amplifiers?
Consider the common-source amplifier shown in Figure P11.50. The NMOS transistor has KP=50 μA/V2, L=5 μm, W=500 μm, Vto=1 V and rd=∞.a. Determine the values of IDQ, VDSQ and gm. b. Compute the voltage gain, input resistance, and output resistance, assuming that the coupling capacitors are short circuits for the ac signal. Repeat Problem P11.50 for an NMOS transistor having KP=50 μA/V2, W=600 μm, L=20 μm, Vto=2 V and rd=∞. Compare the gain with that attained in Problem P11.50.
A certain amplifier has an open-circuit voltage gain of unity, an input resistance of 1 MΩ and an output resistance of 100 Ω. The signal source has an internal voltage of 5 V rms and an internal resistance of 100 kΩ. The load resistance is 50 Ω. If the signal source is connected to the amplifier input terminals and the load is connected to the output terminals, find the voltage across the load and the power delivered to the load. Next, consider connecting the load directly across the signal source without the amplifier, and again find the load voltage and power. Compare the results. What do you conclude about the usefulness of a unity-gain amplifier in delivering signal power to a load?
Suppose that the amplifier as shown has beendesigned to match the source and load resistanceswith the parameters below. (a) What is the amplitudeof the input signal vi needed to deliver 1 Wto the 16- load resistor? (b) How much power isdissipated in the amplifier when 1Wis delivered tothe load resistor?Input resistance Rin = 1 k Output resistance Rout = 16 A = 50 dB

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning