Q1:For the collector feedback amplifier it's parameter B=120and Vcc=16 V, R-3k2, Rg=1kQ, Rp=260kQ determine: 1-S(Ico) ,S(VBE) ,S(B) using T, as the temperature at which the parameter values are specified and B(T2) as 25% more than B(T,). 2-Determine the net change in Ic if a change in operating condition results in Ico increase from 0.2µA to 10HA,VBE drops from 0.7 to 0.5 and B increase 25%. 3-Find the change in Ic if the temperature increase from 25 to 75 (C"). 4-Find Vc,VB, VE IB ,lc,VCE. 5-Explain change value of Vcc ,Rc ,RB ,RE on the amplifier.(what happen in the amplifier).

Q1:For the collector feedback amplifier it's parameter B=120and Vcc=16 V, R-3k2, Rg=1kQ, Rp=260kQ determine: 1-S(Ico) ,S(VBE) ,S(B) using T, as the temperature at which the parameter values are specified and B(T2) as 25% more than B(T,). 2-Determine the net change in Ic if a change in operating condition results in Ico increase from 0.2µA to 10HA,VBE drops from 0.7 to 0.5 and B increase 25%. 3-Find the change in Ic if the temperature increase from 25 to 75 (C"). 4-Find Vc,VB, VE IB ,lc,VCE. 5-Explain change value of Vcc ,Rc ,RB ,RE on the amplifier.(what happen in the amplifier).

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

A unity-feedback system has forward transfer function (see attached). a) Sketch the root locus for this system as K varies from 0 to ∞; b) Use the Routh-Hurwitz test to determine the range of K for the system to be stable; show this value of K on the root locus plot.
Find the closed-loop transconductance, input resistance, and output resistance for the series-series feedback ampliﬁer as shown if the op amp has an open-loop gain of 80 dB, an input resistance of 25kΩ , and an output resistance of 1kΩ. Assume the ampliﬁer is driven by a signal voltage with a 10-kΩ source resistance, and the feedback network is implemented with R2=91kΩ and R1=10kΩ.
Sketch the root locus for unity feedback system with following forward gain function: KG(S) = K(S+1)(S2+2)/S2-9 For what range of K is system stable & unstable.
The circuit as shown is a shunt-shunt feedback amplifier. Use feedback analysis to find the midband input resistance, output resistance, and transresistance of the amplifier if RI = 500 Ω, RE = 2 kΩ, β0 = 100, VA = 50 V, RL = 5.6 kΩ, and RF = 47 kΩ, when vi and RI are replaced by a Norton equivalent circuit. What is the voltage gain for the circuit as drawn?
The voltage gain of an ampliﬁer is described by A(s)= 4π2 ×1018s2 / (s+200π)(s+2000π)(s+2π ×106)(s+2π ×107) (a) What are the mid-band gain and upper- and lower-cutoff frequencies of this ampliﬁer? (b) If this ampliﬁer is used in a feedback ampliﬁer with a closed-loop gain of 100 , what are the upper-and lower-cutoff frequencies of the closed-loop ampliﬁer? (c) Repeat for a closed-loop gain of 40.
Find the desired values below in the feedback amplifier circuit in the figure. a) Find the no-load voltage gain in the amplifier circuit when the Rf resistor is open circuit. b) Voltage and current in amplifier circuit when Rf resistor is open circuit and RL resistor is present Find your earnings. c) When the Rf feedback resistor is connected, the Rf value that makes the feedback current gain Ai/3 find it. Indicate the assumptions you take in your transactions.
An op-amp-based noninverting ampliﬁer has R1 = 15 kΩ, R2 = 30 kΩ, and RL = 20 kΩ. The op amp has an open-loop gain of 94dB , an input resistance of 30 kΩ, and an output resistance of 5 kΩ. Find the loop gain, ideal voltage gain, actual voltage gain, input resistance , and output resistance for the feedback ampliﬁer.
Given a unity feedback system with G (s) =K/ s (s+4). What is the value of K for a damping ratio of 0.5?
FACTS:An amplifier, electronic amplifier or amp is an electronic device that can increase the power of a signal. Classification of the amplifier can be done in 3 different ways. Voltage amplifiers. Current amplifiers. Power amplifiers. QUESTION: You've learned in Module 1 that an Amplifier's Output can be positive or negative which is just natural since we're already dealing with AC signals. But, why do we use negative feedback in Amplifiers?
(a) There are three voltage inputs of V1 = 1V, V2 = 3V and V3 = 4V, and three resistors with the value of 4kΩ, 2kΩ and 1kΩ. Design a single ideal operational amplifier circuit to combine these inputs to produce a single output voltage of Vout = -10.5v with a feedback resistor of Rf = 2kΩ. Provide the sketch and calculation for your designed circuit. (b) Figure 2 below shows a cascaded operational amplifier circuit. Determined the value of the output voltage Vout. (c) Figure 3 shows a bipolar junction transistor circuit in common-emitter configuration. Given that VBE = 0.7 v and ß = 110. Determine the current IB, IC, IE and the voltage VCE.
(a) There are three voltage inputs of V1 = 1V, V2 = 3V and V3 = 4V, and three resistors with the value of 4kΩ, 2kΩ and 1kΩ. Design a single ideal operational amplifier circuit to combine these inputs to produce a single output voltage of Vout = -10.5v with a feedback resistor of Rf = 2kΩ. Provide the sketch and calculation for your designed circuit. (b) Figure 2 below shows a cascaded operational amplifier circuit. Determined the value of the output voltage Vout. (c) Figure 3 shows a bipolar junction transistor circuit in common-emitter configuration. Given that VBE = 0.7 v and ß = 110. Determine the current IB, IC, IE and the voltage VCE. [9 Marks]
Design an inverting amplifier to provide a closed-loop voltage gain of Ay = -22 V/V. The maximum input voltage signal is 30 mV with a source resistance in the range of 1 kls R, < 3 kN. The variable source resistance should introduce a difference in the gain no more than a 2% of the gain factor. What is the range in output voltage?