For the feedback pair, a. Calculate the dc voltages VB₁, VB₂, VC₁, VC₂, VE₁, and VE₂ b. Determine the dc currents IB, IC₁, IB₂ IC₂, and IE₂. c. Calculate the impedances Z; and Zo. d. Find the voltage gain A, = Vo/Vi. e. Determine the current gain A; = 10/1j. V₁ Z HH 1.5 ΜΩ + Q₁ +16 V 68 92 Q2 t Ht ov B₁ = 160 B₂ = 200 Z

For the feedback pair, a. Calculate the dc voltages VB₁, VB₂, VC₁, VC₂, VE₁, and VE₂ b. Determine the dc currents IB, IC₁, IB₂ IC₂, and IE₂. c. Calculate the impedances Z; and Zo. d. Find the voltage gain A, = Vo/Vi. e. Determine the current gain A; = 10/1j. V₁ Z HH 1.5 ΜΩ + Q₁ +16 V 68 92 Q2 t Ht ov B₁ = 160 B₂ = 200 Z

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

Consider the feedback system given the open loop transfer function below G(s)H(s) = K / ( S (s+3) (s+2)) a) Using the Routh-Hurwitz criterion, for which value of K, the poles of the closed-loop system take the pure imaginary value.b) What will be the maximum value of K for the system to be stable?c) Calculate the value of K, where the real value of the complex root of the system is Re{s}=-1. Tip 1: Closed loop transfer function T(s) = G(s) / ( 1+ G(s)H(s)) .Routh HurwitzIn order to perform the criterion analysis, the denominator of the closed-loop function will be examined. Tip 2: The real value of the system complex root Re{s}=-1 is expressed by the following formula f^2(s) = p(s-1) p(s) is the payoff of the closed-loop function.
The circuit as shown is a shunt-shunt feedback amplifier. Use feedback analysis to find the midband input resistance, output resistance, and transresistance of the amplifier if RI = 500 Ω, RE = 2 kΩ, β0 = 100, VA = 50 V, RL = 5.6 kΩ, and RF = 47 kΩ, when vi and RI are replaced by a Norton equivalent circuit. What is the voltage gain for the circuit as drawn?
For the feedback amplifier circuit shown below, assuming the internal resistor in each MOSFETs is infinite ( ro = ∞ ) and gm1 = gm2 = gm2 = 2.5mA/V. a) Draw the small AC equivalent circuit of the below amplifier. b) Determine the overall voltage gain.
Consider the integrating amplifier circuit in Figure 2. Using nodal analysis, derive an expression for vout for the integrating amplifier. In the circuit in Figure 2, exchange the positions of the 0.1uF capacitor and the 5k resistor. a. Use nodal analysis to generate an expression for vout. b. Using this expression, explain what function this circuit performs on an input signal.
The voltage gain of an ampliﬁer is described by A(s) = 2π ×1010s /(s+2000π)(s+2π ×106) (a) What are the mid-band gain and upper- and lower-cutoff frequencies of this ampliﬁer? (b) If this ampliﬁer is used in a feedback ampliﬁer with a closed-loop gain of 100, what are the upper-and lower-cutoff frequencies of the closed-loop ampliﬁer? (c) Repeat for a closed-loop gain of 40.
Consider a unity negative feedback system with loop transfer function shown in Figure where L(s)=GcG(s)=K(s2+6s+1)(s2+5s+1)L(s)=GcG(s)=K(s2+6s+1)(s2+5s+1) Determine the value of K for which the closed-loop system is stable.
Q2: (A): What is the advantages and disadvantages of RC coupled amplifier?
Consider the following statement: In feedback amplifiers, concerning the connections between the direct amplifiers and the feedbacks network, a shunt connectiın at the input part servers to set an increased versiın of the input impedance of the direct amplifier, whereas again a shunt connection at the output part services to set a decreased version of the output imdepance of direct amplifier. Explain what is wrong with the statement above by drawing representative circuit diagrams and outlining the necessary calculations.
The classic feedback ampliﬁer as shown has β =0.125. What are the loop gain T, ideal closedloop gain AIdeal v , actual closed-loop gain Av, and the fractional gain error FGE if (a) A =∞? (b) A =84 dB? (c) A =20?
A unity-feedback system has forward transfer function (see attached). a) Sketch the root locus for this system as K varies from 0 to ∞; b) Use the Routh-Hurwitz test to determine the range of K for the system to be stable; show this value of K on the root locus plot.
In the amplifier circuit seen in the figure below;a) input impedance (ZI),b) calculate the average frequency zone voltage gain AV=(V0 / Vi)
How experimental setup is prepared for a CE transistor configuration. Drawits a h-parameter model. Find amplifier parameters given below using this model- (i) Current gain(ii) Input impedance(iii) Voltage Amplification (AVS) consideration source impedance(iv) Current Amplification (AIS) consideration source impedance