Q1)H ow to stream flow control in hydraulic plants?
Q: For the transistor in the circuit in Figure 3, the parameters are VrN =0.4V, kn = 120µA/V2, and W/L ...
A: a) Given VTN = 0.4 V, KN = 120 µA/V2, W/L = 25
Q: Ex. 3 The Pos;t:Ve y-axis carries a filamenlary Current of 2A in the -ãy direction. Find Ħ at :- A (...
A:
Q: Point charge -4 nC is located at (2,-1,3). Find the potential at(1,0.1) assuming zero potential at i...
A: The value of charge q= -4 nC Position of charge is A(x1, y1, z1) = (2,-1, 3). Position of point wher...
Q: Q Find the capacitance C necessary to improve the power factor to 0.95 lagging in the circuit shown ...
A:
Q: The equivalent resistance between terminals x-y in the resistance network is ww ww 303 20
A: Referring to the given circuit, the 2-Ohm resistor are connected in star combination, so changing th...
Q: Design a voltage divider to provide the following approximate voltages with respect to ground using ...
A: The expression for the voltage-divider rule is given by:
Q: Draw block diagram of solar photovoltaic system which generates DC power and supply AC power(220V an...
A:
Q: What are the three project categories an electrical contractor may choose to browse?
A: There are different projects in the world, and every project needs some specialty for completing it....
Q: Find the Nyquist sampling frequency for the signal x(t)=5cos(1000t)cos(4000t).
A: Using the trigonometric identities, the expression of the given signal can be modified in the follow...
Q: Draw the phasor diagrams for the 2nd approximate equivalent circuit with: - V'2 reference: lagging ...
A:
Q: Given that Z1 = 10+j5 and Z2 = 20- reduce Z1+Z2, Z1-Z2,Z1Z2 and Z1/Z2 to rectangular form.
A: When we add or subtract two complex number the real part is added or subtracted to real part and ima...
Q: Find the midband gain and the frequencies of the poles and zeros of the commonemitter amplifier as s...
A: Given fT = 500 MHz, Cµ = 1 pF, ID = 0.2 mA, VDS = 5 V Calculating transconductance of the transistor...
Q: What factors explain the ampacity of the wire
A: The ampacity is defined as the property of the conductor which will carry the maximum amount of the ...
Q: CT -2: Answer all parts
A: a) A full wave rectifier with a capacitor input filter provides a DC output voltage of 35 V to a 3.3...
Q: Electrical Engineering Question
A:
Q: What is the instantaneous power delivered to the inductor?
A:
Q: S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / pha...
A: As per the policy attempting only first question, Given: Vs = VR = 115 Kv
Q: Starting from the Norton equivalent circuit with a resistive load RL attached, find an expression fo...
A: The circuit show the Norton’s equivalent network: By Current Division rule current through load (...
Q: The primary of a certain transformer takes 0.7 A at a power factor of 0.5 when it isconnected across...
A: Given that, Transformer ratio= ½, I2’= 10* Transformer ratio =10 (1/2)=5
Q: S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34...
A:
Q: Q2: A 4000/400 V, 10 kVA transformer has the following constants:Primary and secondary winding resis...
A:
Q: The directivity of an antenna is 12 dB. What will be the beam solid angle of the antenna? Express th...
A: If D is the directivity of an antenna, then the directivity in decibels can be expressed as Here, t...
Q: CHOOSE Which of the following network types guarantees both communication peers full bandwidth of th...
A: In the packet-switched networks, data is transferred separately. This transfer occurs in small block...
Q: Requirement: Show your calculation
A: Given data: The demand for power supply is 200 per hour. The productive time per hour is 72 minutes....
Q: In the circuit diagram of the Fig. 3, the voltage drop across Z1 is (10+j0) volts. Find the ollowing...
A: Circuit diagram is given, Voltage across is given,
Q: We have an op amp with a maximum output voltage range from −4.5 to +4.5 V. The maximum output curren...
A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...
Q: Q2. For the circuit given below calculate Rs and Rp to set Q point (Ins = 2mA, Vps- 2V) if transisto...
A:
Q: b. For the network in Fig. 3, assuming r, as infinite, determine the following: i Lower cutoff Frequ...
A: Part (i): The expression for the transconductance is given by:
Q: For the circuit shown, find the value of coupling coefficient "k" when the total consumed ?power is ...
A: The circuit diagram is given below, The total equivalent resistance of the circuit is,
Q: What will be the free space path loss if the distance between the two isotropic antenna is 2.5 km an...
A: The free space path loss is dependent on frequency. It can be expressed as
Q: What is the Correlation between Resistivity and Earth Materials?
A: Resistivity is basically a factor that helps in determining the characteristic property of any mater...
Q: 3. Realize the transfer function H(z)=(1+0.6z1} in the following forms: (i) Cascade of one first-ord...
A: Part (i): Consider the given transfer function,
Q: how do U solve this
A: Part a: The expression for the magnetic field due to long current-carrying wire,
Q: QI: For the measurements given below, find: a. The arithmetic mean b. The standard deviation, and th...
A: Since you have asked multiple questions in a single request, we will be answering only the first thr...
Q: Question 1 In the single-phase diode rectifier circuit shown in Figure 1 and a constant de load curr...
A:
Q: Consider the circuit shown in FigureP13.24 . a. Find an expression for the output voltage in terms o...
A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for yo...
Q: For the two port network shown. Calculate the maximum average load power Z11=162 9A Z12=-122 142 162...
A:
Q: Find Io in the circuit of Figure below using superposition ? sa 20 V
A:
Q: Be able to state and use Ohm’s law For the circuit shown, If vg=1 kV and ig=5 mA, find the value of ...
A: GIVEN: Vg = 1 kV Ig = 5 mA
Q: Q4/A 25 KVA transformer supplies a load of 12 KW at a power factor of 0.6 lagging. If additional uni...
A:
Q: It consists of a vacuum Q3. The vacuum diode works mostly like a modern diode. container with cathod...
A:
Q: Given the potential V = 10 sin 0 cos ø, (a) Find the electric flux density D at (2, a/2, 0). (b) Cal...
A:
Q: The switch in the circuit has been in position a fora long time. At t=0, the switch moves instantan...
A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for yo...
Q: What unit of measurement is used for fhe diameter of fhe wires
A: The unit of the measurement used for the wire diameter is Mil. A mil is known as the thousand part o...
Q1)H ow to stream flow control in hydraulic plants?
Step by step
Solved in 2 steps
- What factors affect the stability of a power system, and why is stability important?Answer the following a) Explain the term “suppressed demand “, and give THREE instances in which suppressed demand occurs in a distribution system. b) Electricity demand is affected by a number of economic determinants. Mention any FOUR of such economic factor. c) Long-term forecasting of electrical load is associated with a high degree of uncertainties. Mention any THREE reasons or causes of this uncertainty. d) Give any FIVE drivers or factors that affect total load demand or electricity consumption. Please answer all, I prefer it all answeredD.a. Which one of the following PM programs is usually the largest for a typical manufacturing facility?A. LubricationB. ElectronicC. ElectricalD. MechanicalD.b. The true purpose of uptime inspection PM is toA. keep the PM staff working during low maintenance periods.B. locate problems that occur on a random basis.C. supplement the lubrication PMs in looking for dry bearings and other lubrication problems.D. look for common recurring problems in equipment. D.c. When machines fail shortly after they’ve been built and installed, the failures are termedA. singularity failures.B. independent component failures.C. short-term failures.D. infant mortality failures.