Q(2-3)A gas-turbine power plant operates on Brayton cycle. The air pressure inside the combustion chamber is 1100 kPa. The pressure at the turbine exist is 1.10 bar. Using local thermometers on site, the maximum temperature reached in the system is 1311 K while the minimum temperature in the system is 220. The working fluid is air, which enters the compressor at a rate of 120 m3/min and leaves the turbine at 460°C. Assume the compressor has no deviation. Determine: The compression ratio Turbine isentropic efficiency % Actual temperature inter the combustion chamber in K

Q(2-3)A gas-turbine power plant operates on Brayton cycle. The air pressure inside the combustion chamber is 1100 kPa. The pressure at the turbine exist is 1.10 bar. Using local thermometers on site, the maximum temperature reached in the system is 1311 K while the minimum temperature in the system is 220. The working fluid is air, which enters the compressor at a rate of 120 m3/min and leaves the turbine at 460°C. Assume the compressor has no deviation. Determine: The compression ratio Turbine isentropic efficiency % Actual temperature inter the combustion chamber in K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PART D only A gas-turbine power generator operates on an ideal air-standard Brayton cycle 1 → 2 → 3 → 4 shown in Fig. 1. The gas temperatures at the compressor inlet, compressor exit, and turbine inlet are T1 = 300 K, T2 = 600 K, and T3 = 1200 K, respectively. Solve PART D below using the variable specific heat assumption PART D - Evaluate the thermal efficiency η of the cycle and the back work ratio rBW = wC/wT.
A gas turbine power plant operates on a simple thermodynamic cycle. The ambient conditions are 100 kPa and 24 °C. The air at this condition enters the engine at 150 m whose diameter is 0.5 m. The pressure ratio across the compressor is 13, and the temperature at the turbine inlet is 1400 K. Assuming ideal operation for all components and specific heats for air and products separately. In addition, neglect the mass of fuel burned. Do the followings: d. Determine the pressure and the temperature at the turbine exit, e. Compute the power produced by the turbine f. Available specific work g. The thermal efficiency.
Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications: - A pressure ratio of 14.- The gas temperature is 300 K at the compressor inlet and 1400 K at the turbine inlet.- The mass flow rate of air is 0.783 kg/s Under the assumption of standard air, perform the following:1. The gas temperature of the compressor and the turbine exits, 2. Back-work ratio 3. Find the power output 4. Compare the power output of the basic Brayton cycle with the power output of the best modified Rankine cycle. 5. Compare the final efficiency of the basic Brayton cycle with those obtained from Project-1 for the modified Rankine cycle. How would you explain that the Brayton cycle is more preferred over the Rankin cycle in the power plant station? For the gas turbine plant described in Task.1, investigate the principles of operation of a gas turbine plant by considering the following: 1. Construct TS and PV…
A power plant uses a gas-turbine to produce electricity. Assume that the gas-turbine operates on the ideal Brayton cycle has a pressure ratio of 8. The outside air temperature is 27 C and without preheating, the air is drawn into the compressor. The air compressed in the compressor and its pressure and temperature increase. Thereafter it is supplied into the combustion chamber where its temperature increases to 1023 C at constant pressure. Thereafter, hot air is drawn into the turbine. By considering the air-standard assumptions, determine (a) the gas temperature at the exits of the compressor and the turbine (b) the back work ratio (c) the thermal efficiency
In a closed cycle gas turbine there is two stage compressor and two - stage turbine. All the components are mounted on the same shaft. The pressure and temperature of air at inlet to the first stage compressor are 1.5 bar and 20 °C respectively . The maximum cycle pressure and temperature are limited to 750 ° C and 6 bar. A perfect intercooling and reheating are used between the compressors and the turbines. A regenerator whose effectiveness is 0.7 was employed. Assuming the compressors and turbines efficiencies as 0.82 , calculate : a . Thermal efficiency of the cycle. b. Mass of working fluid for a power output of 350 kW. Assume the working fluid is air has c = 1.005 kJ / kg K , y = 1.4
ı couldnt do this can u help me please? An ideal gas turbine cycle with regeneration using air as the working fluid has a pressure ratio of 6. At the beginning of the compression, pressure is 100 kPa and temperature is 300 K. The regenerator has an effectiveness of 70 percent, and the air enters the turbine at 1200 K. Assuming constant specific heats for air at room temperature, determine, a) the amount of heat input,b) the thermal efficiency.
1. A Rankine cycle with reheating has a throttle pressure of 135 bars at the turbine inlet and 28 bars reheatpressure, the throttle and reheat temperature of the steam is 550C, condenser pressure is 0.035 bar, massflow rate of steam is 10 kg/sec. Draw the T-s and schematic diagram of the cycle and determine the following:(a) ideal turbine work(b) ideal pump work(c) theoretical thermal efficiency(d) the steam rate(e) heat rate of the cycle(f) actual work of the pump if pump isentropicefficiency is 89%(g) actual turbine work if turbine isentropic efficiencyis 90%
A newly purchased sedan car operates on an ideal thermodynamic cycle. The engine has acompression ratio of 10. The ambient air pressure is 1 bar while temperature is 21 ºC. Themaximum temperature in the engine is 1600 K. Draw the ideal power cycle and label it.Utilizing the air-standard assumptions, determine (a) the gas temperature at the exits of thecompression and the expansion processes, (b) the specific works of compression, expansionand net, (c) heat supplied to the engine and (d) the thermal efficiency.
Q.8 In a regenerative steam cycle employing one open feed heater, the steam is supplied to the turbine as dry saturated at 40 bar, and exhausted to the condenser at 0.35 bar. The intermediate bleed pressure is 10 bar. Sketch the layout of the plant and show on the temp | entropy diagram the pressure under gone by the steam, neglecting the pump works, calculate: A. The mass of steam bled from the turbine per Kg of steam leaving the boiler. B. The thermal efficiency of the plant. C. The thermal efficiency of the plant without feed heating. D. The heat rate in (kJ/kW.hr) for the plant with and without feed heating.
In an ideal reheat cycle, the steam throttled condition is 8 MPa and 480 degree C. the steam is then reheated to MPa and 460 degree C. the turbine exhaust is 60 degree C. The required values of some state point properties are tabulated below. 2. Determine the quality of steam at the last stage of isentropic expansion in the turbine.
A simple actual Brayton cycle using air as the working fluid has a pressure ratio of 8. The minimum and maximum temperatures in the cycle are 310 and 1160 K. Assume the start of isentropic compression being state point 1, and an isentropic efficiency of 75 percent for the compressor and 82 percent for the turbine. Account for the variation of specific heats with temperature. [Hint: Do not consider the average values of specific heats. Use the concept of relative pressures.] Draw this actual Brayton cycle on T-s Also draw the schematic block diagram of the gas-turbine power plant which works on this cycle. Determine: the air temperature at the turbine exit in K, the net work output in kJ/kg, and the thermal
Q1/ Ideal reheat cycle, has the following specifications: Boiler pressure is 200 bar and Condenser pressure is 0.22 bar and Reheat pressure is 60 bar , Turbine inlet temperature is 500 C and Reheat temperature 480 C Calculate: quality at turbine exist, thermal efficiency, and steam rate.