Q2-A hollow stainless-steel cylinder having an inside diameter of 4 cm and thickness of 1 cm is exposed to a convection environment at 30 C, h=50 W/m2 C. Heat is generated uniformly in the cylinder at the rate of 1 MW/m3. Determine the steady state temperature distribution in the cylinder. What are (1)-the location and (2)-the value of the maximum temperature in the cylinder? Assume the inside surface is insulated.

Q2-A hollow stainless-steel cylinder having an inside diameter of 4 cm and thickness of 1 cm is exposed to a convection environment at 30 C, h=50 W/m2 C. Heat is generated uniformly in the cylinder at the rate of 1 MW/m3. Determine the steady state temperature distribution in the cylinder. What are (1)-the location and (2)-the value of the maximum temperature in the cylinder? Assume the inside surface is insulated.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.34P: 2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material...

See similar textbooks

Similar questions

An iron block cools down from 200°C to the room temperature of 27°C,when outdoor is 5°C, heating the room. Determine the maximum theoreticalamount of heat that can be supplied to the house as the iron cools down to27°C.
A camper has a propane-powered refrigerator. The refrigerator consumes approximately 0.50 kgof propane per day. When propane is burned completely, it releases approximately 50. MJ/kg.The interior of the refrigerator is maintained at an average temperature of 2.0 °C, and theexterior temperature is 22 °C. Assume that the refrigerator has a surface area of 2.0 m2 and thatthe insulation has an R-value of 3.2 K · m2/W.(a) At what rate does heat flow into the refrigerator?(b) At what rate must the refrigerator remove heat from its interior?(c) How much energy is released per second from the propane combustion?(d) How much heat is delivered to the room?
THERMOFLUID A student living in a 3-m X 4-m X 4-m dormitory room turns on her 100-W fan before she leaves the room on a summer day, hoping that the room will be cooler when she comes back in the evening. Assuming all the doors and heat trans windows are tightly closed and disregarding any heat fer let through the walls and the windows, determine the temperature in the room when she comes back 8 h later. Use specific heat values at room temperature, and assume room to be at 100 kPa and 20°C in the morning she leaves.
In determining the average rate of heating of a tank of 20% sugar syrup, thetemperature at the beginning was 20°C and it took 30 min to heat to 80°C. Thevolume of the sugar syrup was 50 ft3 and its density 66.9 lb/ft3. The specific heat ofthe sugar syrup is 0.9 Btu lb-1°F-1.(a) Convert the specific heat to kJ kg-1°C-1.(b) Determine the rate of heating, that is the heat energy transferred in unit time, in SI units (kJ s-1)
what is the temperature T at distance X = L1 = 8 cm under the steady-state condition?
Thermodynamics. Help me out with detailed explanation. 1. Describe in detail the Joule-Thomson experiment. Include in your descriptionthe aim, apparatus, setup, results, relevant formulae and potentialapplication(s) of the experiment. 2. Explain, using appropriate example(s), how does Clausius statement of thesecond law set an upper limit to the thermal efficiency of any heat engine, andto the coefficient of performance of a refrigerator.
An insulated rigid tank initially contains 1.5 lbm of helium at 80°F and 50 psia. A paddle wheel with a power rating of 0.02 hp is operated within the tank for 30 min. Determine (a) the final temperature and (b) the final pressure of the helium gas. Specific heat of helium, Cv=0.753 BTU/lbm oF
5. A 4-m x 5-m x 7-m room is heated by the radiator of a steam-heating system. The steam radiator transfers heat at a rate of 10,000 kJ/h, and a 100-W fan is used to distribute the warm air in the room. The rate of heat loss from the room is estimated to be about 5000 kJ/h. If the initial temperature of the room air is 10°C, determine gow long it will take for the air temperature to rise to 20oC. Assume constant specific heats at room temperature where CAIR = 0.768kJ/kg-K. Draw a figure or FBD that will support the problem. Explain each step by step formula.
Completely solve. Write legibly. determine the heat and nonflow work of the polytropic expansion of steam from 2.8 MPa and 340°C to 0.76 MPa at 200°C. (Given answer: -3000 kJ/kg, -3012.5 kJ/kg)
Located near the bottom of an insulated cylinder is a rigid plate. Between the rigid plate and the bottom of the cylinder is 0.4 kg (ma) of air at 250 kPa (Pa1) and 300 K (Ta1). Between the rigid plate and a moveable piston 0.5 kg (mw) of superheated water vapor at 300 Celsius (Tw1) and 100 kPa (Pw1) is added. Consider these to be the initial conditions (state 1) of this multi-component system. The rigid plate is conductive allowing heat to pass between the air and water vapor, but the piston is well insulated. The water vapor is manually compressed in an unknown process until the volume of water vapor (Vw2) is halved and the pressure is 200 kPa (Pw2), at which point the air and water vapor are in temperature equilibrium.Determine the following:A. The change in entropy of air and water in kJ/K B. The change in entropy of the combined system, S2-S1, in kJ/K, neglecting the mass of the rigid plate C. The entropy produced, σ, of the combined system during the process
A long roll of 2-m-wide and 0.5-cm-thick 1-Mn manganesesteel plate (ρ = 7854 kg/m3 and cp = 0.434 kJ/kg·°C)coming off a furnace at 820°C is to be quenched in an oil bathat 45°C to a temperature of 51.1°C. If the metal sheet is movingat a steady velocity of 10 m/min, determine the requiredrate of heat removal from the oil to keep its temperature constantat 45°C.
Wet steam at 200°C and 20% moisture is compressed in an irreversible adiabatic process to a process of 2.30 MPa and a temperature of 225°C. (b) Determine the compression efficiency in %. (a) Determine the compression internal reheat in Kj/Kg.