Q2- A steel pipe assembly supports a concentrated load of P = 22 kN as shown in Fig. 2. The outside diameter of the pipe is 142 mm and the wall thickness is 6.5 mm. Determine the normal stresses produced at point H.

Q2- A steel pipe assembly supports a concentrated load of P = 22 kN as shown in Fig. 2. The outside diameter of the pipe is 142 mm and the wall thickness is 6.5 mm. Determine the normal stresses produced at point H.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 8.9 The stresses across two mutually perpendicular planes at a point in an elastic body are 120…

Q: Q/2 A cylindrical metal pressure vessel 400 mm, 15 mm in diameter and thickness respectively. There…

Q: Problem 2 For the state of plane stress shown below, determine the principal stresses, the ma plane…

Q: At a point on the free surface of a stressed body, the normal stresses are 20 ksi (T) on a vertical…

Q: Q2-A reinforced concrete column of 250mm x 250mm cross section is designed to carry an axial…

Q: А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN…

A: In compression, we examined a cube with a 2.5 cm edge, as illustrated in the picture. It failed…

Q: For a body under three dimensional stress state, describe the procedure for obtaining the absolute…

A: When stresses are applied in a body in all the three dimensions. Then, all the stresses can be…

Q: Q2. A mild steel shaft transmits 'P' kW at 'N' r.p.m. It carries a central load of 900 N and is…

A: Shaft is a rotating element that transmit power and rotation.

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Given data: - The pressure inside vessel is P = 150 psi. The length of the vessel is L ft. The…

Q: A point On a free surface of a machine point (E = 214Gpa, G= 83Gpa) the stress state is shown on the…

A: GIVEN :- E = 214Gpa G= 83Gpa σy=15 MPaσx=-30 Mpaζxy=25 MPa

Q: A state of stress is specified in the figure shown below. Determine the Normal stress ox (mPa) on…

Q: Q3. For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

A: given data inner radius = 20 mm outer radius = 40 mm internal pressure = 5 Mpa

Q: Q2) The lower ends of the three steel rods shown in (FIG. Q2) are at the same level before the force…

Q: the stresses at point A.

A: To find Stresses at point A

Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.

A: σx = 90 Mpa σy = -60 Mpa Txy = 20 Mpa

Q: Q2: A rigid platform weighing 53.5 kN is supported by three equally spaced rods. The arrangement is…

A: Given that, Weight of platform, W=53.5 kN,Temperature rise, ∆T=55.5 °C, Consider the properties as…

Q: Q1) The frame shown below is fixed at point Q and subjected to the axial load at free end in both…

Q: Q2) In Fig.(2), the shaft is subjected to reversed loads, F = F 2700 N and P = F 1350 N, where these…

Q: 5. The normal and shear stresses acting on one plane passing through a point in a soil mass are 120…

Q: In a volume element with dimensions dx, dy, dz the negative y-face has a 2 MPa stress in the…

Q: The components of plane stresses at a critical point are shown in the following figure. Determine…

Q: A load of 7,000 N acts on the machine part shown in Fig. 5a. The machine par thickness of 15 mm…

Q: In a cylindrical container, Gas is compressed to a pressure of 3 MPa. If the cylinder has a diameter…

A: Boiler shells, pressure tanks, pipes, and other low-pressure processing equipment all use…

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa,…

A: Given data Internal diameter of steel cylinder (Di) = 160 mm internal radius (ri) = 80 mm outer…

Q: QUESTION 3: [Thin-walled Pressure Vessels] 1. A cylindrical pressure vessel is fabricated from steel…

A: Q.3)Given: Thin walled pressure vessels1)Thickness t=20 mmDiameter of pressure vessel=d=450…

Q: 41.) A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, is…

Q: Design engineers in many situations must justify their selection of material. Your role in a…

A: Pressure, P = 250 psi Thickness, t = 0.25 in Diameter, d = 1 foot = 12 in a) Longitudinal stress…

Q: The compound steel bar shown in Fig. Q1(b) made of three uniform segments marked as 1, 2 and 3 of…

Q: piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º…

Q: Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an…

A: Given data Inner radius = 50 mmOuter radius = 115 mmInternal Pressure =60 MN/m2External Pressure =…

Q: Define the main difference between thick and thin cylinders and give an example for each type of…

Q: Q2/ A negligible weight bracket, subjected to 3 kips load P as shown in Fig. 1. Determine the normal…

A: Given that, Load acting at B, P = 3 kips, All pin diameter, d = 0.4 in, The cross-section area of…

Q: Q4- Draw Mohr's circle for the case as seen in Fig. 4. Determine the principal stresses and the…

A: According to the given information we have stress in x-direction and stress in the y-direction and…

Q: Q1/ (A) - The mechanism of femur bone is approximated as a circular tube (3 cm and 2 cm are the…

Q: 1. For the state of plane stress with x-y axes as shown, do the following: 12 MPa 1.1 draw the…

Q: .For the pressure cylinder shown in fig. 6. determine the radial and tangential stresses for…

A: Given: pi=6 bar=0.6 MPap0=0di=120 mmdo=200 mm

Q: Q2: Determine the state of stresses at point A on the cross section of the pipe shown in Fig. D=50mm…

Q: The state of stress acting at a critical point on a wrench is shown in the figure. Determine the…

A: Given: The state of stress is given as Here, σx=300 MPaτxy=150 MPa

Q: GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane…

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 750kPa. If the allowable…

Q: O Solve two problems on statically indeterminate structures(strain energy method), two on thin wall…

A: Given: The outer diameter of the steel cylinder is D = 360 mm. The inner diameter of the steel…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner…

A: solutionwe have given in the question.outer radius (r0)=260mminner radius (ri)=55mminterval pressure…

Q: A block is subjected to the stresses as shown in Fig. 1. If the allowable compressive normal stress…

Q: P, P. P,

A: given:

Q: • When the state of stress is represented by the principal stresses, no shear stress will act on the…

A: When the state of stress is represented by the principal stresses, no shear stress will act on the…

Q: 4. A cylindrical boiler with hemispherical ends has an outside diameter of 6 ft. If the hoop and…

A: Given Data Outer diameter, 6ft Outer radius, 3ft=3(12)=36in Hoop stress, 15ksi Axial stress, 8 ksi

Q: Q2) For the state of plane stress given on the element below, construct a Mohr's circle. Use circle…

Q: At a point in a stressed body the state of stress on two planes 45° apart is as shown below.…

A: Given:σx=8 MPaτxy=3 MPaθ=45o

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

100%

Strength of Materials

Q2- A steel pipe assembly supports a concentrated load of P = 22 kN as shown in Fig. 2. The
outside diameter of the pipe is 142 mm and the wall thickness is 6.5 mm. Determine the normal
stresses produced at point H.
- 370 mm-
600 mm
Fig. 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cylindrical tank has an inner radius of 750mm and length of 3.0m. Determine its minimum thickness (to nearest mm) if it is subjected to an internal pressure of 150kPa and tangential stress is not to exceed by 12MPa. Indicate the free body diagram
The outside diameter of the steel pipe shown is 220 mm and its wall thickness is 6.0 mm. The upper bearing plate has the same width as the reinforced concrete beam it supports. The total load on the column by the reinforced concrete beam is 550 kN. Determine: A. The length L of the rectangular upper bearing plate if its width is 275 mm. and the average bearing stress between the steel plate and the reinforced concrete beam is not to exceed 6.2 MPa.
an acetylene tank consists of a cylindrical body flat at its base and hemisphere at the other end . the thickness of the metal used in tank is 2mm. the tank has a diameter of 250 mm and 1200 mm long. what is the internal pressure of the tank if the allowable stress of the material is 180MPa a. 3.5 kPa b. 6.8 kPa c. 4.2 kPa d. 5.5 kPa
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
The strut is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of 1,2 m , determine how much it stretches when the distributed load acts on the strut.
Determine the largest weight W in N that can be supported by two wires shown in the figure.The stress in either wire is not to exceed 261 Mpa. The cross-sectional areas of wires AB and ACare 258 mm^2 and 320mm^2 respectively.
The bearings at A and D exert only y and z components of force on the shaft as shown in Fig 7. Determine the smallest diameter of the shaft using maximum shear stress hypothesis theory if the allowable stress is 100 MPa.
What is the stress in a rectangular rod that is 20 mm by 30 mm in cross-section if is supporting a load of 1000 N? Express your answer in N/m2, Mpa, and psi.
A cast iron tube 3m long is completely filled with concrete and used as a vertical strut. if the external diameter of the tube is 40mm and the wall is 35mm thick, determine the maximum compressive load, the composite strut can support if the stress in the concrete is not to exceed 2N/mm^2. By how much should the strut shorten under the load. For cast iron Ea=100 GN/m^2 and for concrete , Eb=10 GN/m^2
The cylinder is shown in Figure is made of steel having a specific weightof gst = 490 lb>ft3. Determine the average compressive stress acting atpoints A and B.
A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE THE MINIMUM THICKNESS OF THE TANK IF THE STRESS IS LIMITED TO 70 MPa. (note: Diam = L1, Height = L2) L1 = 5 L2 = 7
A steel pipe 1.5m in diameter is required to carry an internal pressure of 750 KPa. If the allowable tensile stress of steel is 140 MPa, determine the required thickness of the pipe in mm.