Q2/ Beam AB is subjected to a uniform load of200N/m and is supported at B by post BC, asshown in Fig. If the coefficients of static friction atB anddetermine the force P needed to pull the post outfrom under the beam. Neglect the weight of theCareHB = 0.25 and µc = 0.6 and%3D0.75 mle 25 mmembers and the thickness of the beam.

Answered: Image /qna-images/answer/4698c7bf-20c0-4168-8bae-23f6809dee89.jpg

Q2/ Beam AB is subjected to a uniform load of 200N/m and is supported at B by post BC, as shown in Fig. If the coefficients of static friction at B and C are determine the force P needed to pull the post out from under the beam. Neglect the weight of the members and the thickness of the beam. HB 0.25 and µc 0.6 and %3D

Q2/ Beam AB is subjected to a uniform load of 200N/m and is supported at B by post BC, as shown in Fig. If the coefficients of static friction at B and C are determine the force P needed to pull the post out from under the beam. Neglect the weight of the members and the thickness of the beam. HB 0.25 and µc 0.6 and %3D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.51P: The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest...

See similar textbooks

Similar questions

Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
The aluminum pipe shown in Fig. is used to support a load of 150 kip.Determine the maximum displacement at the top of the pipe if the load is(a) applied gradually, and (b) applied by suddenly releasing it from the topof the pipe when h = 0. Take Eal = 10(103) ksi and assume that thealuminum behaves elastically.
A load of W = 34 kN is lifted through a boom 'BCD' as shown in the figure. The boom makes an angle of 60 degrees with the vertical. Neglect the weight of the boom for this problem, L1 = L2 = 2.6 m. The pulley at 'D' is frictionless. d.) What is the vertical component at 'B' in kN? e.) Calculate the total reaction at 'B' in kN. *Round off in 4 decimal places. Thank you.
Rod AB leans against the wall with a coefficient of static friction, μSB = 0.2. The contact surface at A is smooth (μSA = 0). Find the minimum force P necessary to prevent rod AB from sliding, given:WRod = 40 lbs, L1 = 7 ft, θ = 42 °.
please very urgent The bank in the figure is thought that a person is sittingthe force exerted on the board as 300 NIt is given. Elasticity of the boards that make up the benchmodule E = 7 GPa, the width of a board is 150 mm andSince the height is 30 mm, the person sitsCalculate the slump at the point. (Hint: ABas if built-in board A and BThink about it.) Dimensions ar in mm.
A homogenous bar with length l and weight w lb rests horizontally as shown in Fig 9-37 with its free end on a block of weight W, the block W is at rest on a plane inclined at the angle α with the horizontal. Determine the necessary coefficient of friction μ between the block and the plane for equilibrium. Assume no friction between the bar and the block. Give solution. [Ans. μ=(sin⁡ 2α) / (w / W+2 cos2 α)]
Gate AB retains water as shown in the figure. The gate is supported every 2 m (perpendicular to the plane of view) by member BC, which is attached to a 2000 kg mass at point C. What minimum static coefficient of friction μs, along the contact surface between the mass and its base, is needed for the gatestructure to be in equilibrium? There are pins at pointsA, B, andC.
An object weighing 40 N is drop from a height of 4 m and hits a vertical steel rod on top. Determine the stress of the rod. Diameter 4 mm, length 4 m. Neglecting buckling.
A square thread jackscrew has a 2 threads per inch. It is to lift 15tons. The friction radius of the collar is 1 in. The coefficient offriction between the threads of the screw and base is 0.15, thatbetween the screw and the collar is 0.13. Determine:a. The diameter of the root of the screw if theallowable stress in compression is 6 000 psi.b. The torque required to turn the screw.c. The pull required at the end of a 5 ft bar raises theload.d. The twisting moment exerted at the root of thethreads.e. The power output of the screw if it is turning at 60rpm.f. The power input of the screw.g. The efficiency of the screw and collar
A load G1 is placed on the horizontal plane. A rope is attached to it, which is passed over a stationary pulley, and a load of weight G2 is attached to the other end of the rope. Determine the equilibrium position of the load G1 (length x) if the height x and the coefficient of friction µ are known.Note: The answer is x=h\tan alpha i want to understdan how this problem is fixed.
The homogenous 360 kg block rests against the vertical wall, for which the coefficiewnt of friction is 0.25. A force P is applied to the midpoint of the right face in the direction shown in thre figure. What range of values may P have without disturbing equilibrium. Give solution. (Ans. 5260 N < P < 7890 N)
A 10 m long beam weights rests against the smooth wall as shown. The weight of the beamis 2 N. The coefficient of static friction between the beam and the ground is 1.4. Determine themaximum magnitude of force P that can be applied before the beam slides.