Q2) Centrifugal pump, works between two large and free surface tanks, of efficiency 80% driven by a motor of efficiency 80% to lift water through a height of 130 ft. Pumping is through 980 ft of 3.5 in diameter at rate of 300 gpm. If the friction factor is 0.027. What is the consumed power by the motor? (take a=1)

Q2) Centrifugal pump, works between two large and free surface tanks, of efficiency 80% driven by a motor of efficiency 80% to lift water through a height of 130 ft. Pumping is through 980 ft of 3.5 in diameter at rate of 300 gpm. If the friction factor is 0.027. What is the consumed power by the motor? (take a=1)

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Similar questions

A pump must be designed to deliver 6 m3/s of water againsta head of 28 m. The specified shaft speed is 20 r/s. Whattype of pump do you recommend?
A pump rated at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, how much electricity is required to keep the process running for 24 hours? Choices: A. 29.37 kWh B. 35.28 kWh C. 56.71 kWh D. 43.21 kWh
A pump discharges 50 tons of water per hour to a height of 8 m, overall efficiency of the pumping system being 69%, what is the input and output power?
A centrifugal pump having an overall efficiency of 75%, delivers 1850 liters of water per minute to a height of 20 m through a pipe 10 cm diameter and 100 m long. If f=0.012, calculate the hp to drive the pump.
If a pump requires a minimum of 2.75m of NPSH, how high (absolute value in meters) can the centerline of the pump be located above the top of an open tank that supplies a 27°C-water to the pump? The water tank is 1.83m high which is filled to the brim, and the total pipe friction is 0.70m.
(a) the total dynamic head (TDH) in meters (b) the water power (WP) in kW (c) the pump mechanical efficiency (%) if the power input to the pump is 15hp
If a pump requires a minimum of 2.75 m of NPSHA, how high can the centerline of the pump be located above the top of an open tank that supplies 27 C water to the pump? The barometer reads an average of 732 mmHg throughout the year. The tank is 1.82 m high. The pipe friction is 0.7 m and the velocity is 1.22 ?/? .
A centrifugal pump is to be placed at the bottom of a vertical shaft 350 m deep to deal with an inflow of water at the rate of 22 l/s. The choice lies between three pumps, one of 115 kW, one of 185 kW and one of 300 kW. Each pump has efficiency of 85%. 1. For each pump, calculate the approximate rate (litres/s) that can be pumped (ignore the friction and velocity heads) 2. For each pump, calculate the number of hours the pump would have to run (during a 24-hour day) to handle the inflow. 3. Which pump should be installed if the capacity should be at least double that required in case of flooding?
A centrifugal pump(efficiency 86%) lifts water through a total height of 42m from reservoir to discharge. Pumping is through 300m of 75mm diameter pipe at the rate of 20li/s. If pipe friction factor, f = 0.025, what KW is required? Answer: 9
Q9: Find the specific speed and power consumption for pump having the following properties: (Q=0.1 m3/s), (speed=725 r.p.m) and (head =15 m).
What are centrifugal pumps' standard pump input power (kW) and water power (kW)?
A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a manufacturing plant. The pump operates against a head of 30m and has an efficiency of 70%. What quantity of water (in m^3/s) can the pump deliver?