I need the answer as soon as possible Q2For the system shown in Figure 1, find the range of the gain K that results in astable closed-loop system.s+ 20s(s + 10)2R(s)KY()Figure 1. System in Q2

Answered: Image /qna-images/answer/4862c09c-895d-46a6-8ef2-c13dce0a6cb6.jpg

Answered: Q2 For the system shown in Figure 1,…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The inverting amplifier in the circuit shown has an input resistance of 500 kΩ, an output resistance of 5 kΩ, and an open-loop gain of 300,000. Assume that the amplifier is operating in its linear region. 1. Calculate the voltage gain (vo/vg) of the amplifier. 2. Calculate the value of vn in microvolts when vg=1 V. 3. Calculate the resistance seen by the signal source (vg). 4. Repeat (a)–(c) using the ideal model for the op amp.
The op amp in the adder-subtractor circuit attached is ideal. A. Find the output voltage v0 given Va = 2V, Vb = 3V, Vc = 5v, Vd = 6V. B. For the values given in A, find V0 if the feedback resistor is replaced with a 100 ohm resistor.
In the circuit below, assuming the ideal opamp, we ask a) determine the circuit gain (Avf = V2 / V1). b) Calculate the gain value when R1 = R3 = 10KΩ and R2 = 16kΩ answer a) Avf=1((R1+R3)/R2) b) Avf=2,25
Using the components listed below, design an amplifier having a voltage gain of −10 ± 20 percent. The input impedance is required to be as large as possible (ideally, an open circuit). Remember to use practical resistance values. Cascade a non-inverting stage with an inverting stage.1) Standard 5%-tolerance resistors.2) Standard 1%-tolerance resistors. (Don’t use these if a 5%-tolerance resistor will do, because 1%-tolerance resistors are more expensive.)3) Ideal op-amps.4) Adjustable resistors (trimmers) having maximum values ranging from 100 Ω to 1 MΩ in a 1–2–5 sequence (i.e., 100Ω, 200Ω, 500Ω, 1 kΩ, etc.). Don’t use trimmers if fixed resistors will suffice.
Find the relationship between the output and the input in the amplifier circuit depicted in Figure Q3.a & Q3.2. State any assumptions you make. [Derive the formula of gain]
1. For n-stage analog amplifier circuit, if the voltage gain of each stage is Adi and the op amp common-mode rejection ratio is CMRRi (I =1~N): a) derive the mathematical expressions for the CMRR for the whole circuit b) analyze which stage’s CMRR has the most influence on the overall CMRR.
For an op-amp having a slew rate SR = 8 V/ms, what is the maximum closed-loop voltage gain that can be used when the input signal varies by 0.5 V in 10 ms? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.
Based on the simulation’s results, explain the function of a differential amplifier. (Hints: comment on the shape of Vo1 and Vo2, explain what would happen if V1 and V2 were the same, reflect on why it is important that an ideal op-amp has infinite input impedance).
1.Design a noninverting amplifier (as shown) with a gain of 6, using a 75 kΩ resistor in the feedback path. Draw your final circuit daigram. 2.Suppose you wish to amplify input signals in the range −2.5 V≤vg≤1.5 V. What are the minimum values of the power supplies that will keep the op amp in its linear operating region?
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792
What is the cut–off frequency of an op-amp if the unity-gain frequency is 2.8 MHz and the open-loop gain is 200,000? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below. ASAP.
What is the CMRR of the op-amp in dB if the open-loop differential voltage gain of 200,000 and a common-mode gain of 0.3? Show the details of your work. Write your solution on a white typewriting paper, scan it in JPEG format and upload it to the space provided below.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Q2 For the system shown in Figure 1, find the range of the gain K that results in a stable closed-loop system. s+ 20 s(s + 10) R(s)- Y() Figure 1. System in Q2