Answered: Q2/ In equilibrium position shown in…

Q2/ In equilibrium position shown in figure below. The uniform bar (AB) has a mass of (50 kg) and supports the (200 kg) load at (A).Calculate the tension (T) in the cable and the force at (B)?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.27P: A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the...

See similar textbooks

Related questions

Q: x Slide 1 X Final exam (Remotely Procto #lockdown Question 1.16 The state of stress at a point is…

Q: The 250-lb concrete block A is released from rest in the position shown and pulls the 400-lb log up…

A: Answer: The velocity of the block as it hits the ground at B: 15.27 ft/sec

Q: By using the Mohr's circle approach, c. Construct the Mohr's circle for the stress element shown in…

A: Givenσx=45MPaσy=-60MPaτ=30MPa

Q: a=2.1m (1) c = 2m B b = 3.1m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa…

Q: 10m 10m 4. An ideal Brayton cycle has a low and high pressure of 14.7 psia and 100 psia. The…

Q: a=2.1m (1) c = 2m b=3.1m d = 1.8m P = 30 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa…

Q: hat is the relationship of mass of block and angle of response. What can be conclude on the given…

A: we have to study the relationship between mass of block and angle of repose

Q: Determine the mass moments of inertia (in slug-ft²) and the radii of gyration of the steel machine…

Q: he buoy shown in (Figure 1) is made from two omogeneous cones each having a radius of 1.5 ft. Figure…

A: h=0.8ft r=1.5ft

Q: Find the two forces Fbc & Fac as :shown in the figure below

Q: A Japanese spacecraft Hayabusa-2 landed on an asteroid Ryugu on 21st February 2019 in an attempt to…

A: Given questions: Write down the rocket equation and determine at its maximum momentum the fraction…

Q: (a) The rotating elements in machine system often generate unbalance forces due to unbalance mass…

A: Introduction: Unbalance is described as an unbalanced mass distribution that causes the mass axis to…

Q: Use this data to compute the location and y to the center of gravity G of the car.

A: Given question: We have to compute the center of gravity of the car from the given data.

Q: 1. Assume 1 kg of steam expand isentropically from 2 MPa and 360°C to 0.040 MPa. Find: a) work for…

Q: A 450kN force is needed to punch a 30mm diameter hole in a plate that is 10mm thick. Determine the…

Q: 5.8 Show that for temperatures well below p, the mean free path of a phonon can be expressed as f…

Q: ---- at the end of the fire grate which is utilized in deflectin 7. In a Lancashire steam boiler,…

A: Disclaimer: Since you have asked multiple question, we will solve the first question for you. If you…

Q: A power screw has single square threads. It has a major diameter of 36 mm and a pitch of 6 mm. The…

Q: J 5 A Carnot refrigeration cycle is used to maintain a room at 23 °C by removing heat from…

A: Given: The room temperature, T2 = 23 C The ground water temperature, T1 = 15 C The refrigerant…

Q: In the figure, block 1 has mass m₁ = 460 g, block 2 has mass m₂ = 580 g, and the pulley is on a…

A: Given that: Mass of block 1 = 460 g Mass of block 2 = 580 g R = 5.3 cm When block 2 moves 71 cm in…

Q: The system in the figure is in equilibrium. A concrete block of mass 215 kg hangs from the end of…

A: Given data as per the question Mass of block =215 kg Mass of strut =41.4 kg

Q: A load Q-200kN is applied to a rigid plank MN as shown. At ends M and N, vertical brass and bronze…

Q: A gas metal arc welding test is performed to determine the value of melting factor f₂ for a certain…

A: Gas metal arc welding is a semi automatic or automatic arc welding process which uses a consumable…

Q: A liquid with specific weight of 15500 N/m³ is in the conduit shown. This liquid has zero viscosity.…

A: Specific weight of liquid, γ=15500 N/m3Pressure at A, PA=8 kPa=8*103 PaPressure at B, PB=5 kPa=5*103…

Q: Figure Q1 (b) shows a thin disc mounted on a shaft between two bearings. The thin disc density is…

Q: Q1:A/ If the temperature increases; how would it be effect on ? (Specify your answer with :…

A: Introduction: Temperature Influences The operating temperature has a significant impact on the…

Q: Two kilograms of ice at -24C is heated in an open pan until melts and then evaporates. The saturate…

A: Givenice to saturate vaporm=2kg T1=-24oCT2=100oC

Q: a=2.1m (1) C = 2m B C b=3.1m d = 1.8m P = 30 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa…

Q: Q3-A: Determine the x- and y- coordinates of the centroid of the shaded area. | 60 mm 240 mm 120 mm…

Q: 5. Forces are applied to a door. For each one, determine if the torque is clockwise,…

Q: 1-Use the North West corner to obtain the starting basic feasible solution for the following…

Q: A WATER TANK IS “L1” IN DIAMETER AND “L2” HIGH. IF THE TANK IS TO BE COMPLETELY FILLED, DETERMINE…

Q: In the Figure 6, the absolute force value in the bar AB is (in kN): Figure 6: 5 m X A 20 KN 5 m 5 m…

A: Static equilibrium equations are used while calculating forces in trusses in case of Method of…

Q: 4. A mass-spring and viscous-damper system is shown in Figure 2. 100 N/m FO 5 kg 30 N.s/m Figure 2 F…

Q: Calculate the height of capillary rise in a glass capillary tube having a radius of 3.5 x10-5 m. The…

Q: A rod has a radius of 10 mm. If it is subjected to an axial load of 15 N such that the axial strain…

Q: ater flows through a horizontal coil heated from the outside by high temperature flue gases. As it…

A: given

Q: Superheated steam enters the turbine of a steam power plant at 5 MPa and 450 ºC, and exits at 10…

A: Given:P1=5 MPaT1=450°CP2=10 KPaη=90%m=10 Kg/s

Q: 10. Using 5x5 grids, determine the equation for steady state temperature distribution at T21, T22…

A: Introduction: The precise form of the steady-state temperature distribution is determined by the…

Q: A particle is moving on a straight line with a velocity v = 25 m/s which is increasing at a rate of…

Q: An ideal reheat regenerative Rankine cycle with one open feedwater heater. The boiler and condenser…

Q: Q4A: Calculate the forces in members AG,AB, CG, GF and CF for the truss shown. 2 kN C 2 m D A 4 kN 2…

Q: 3- In an air standard Brayton cycle, the pressure ratio is 6. The condition of air at the beginning…

A: given; pressure ratio(r)=6 pressure at beginning (P1)=1bar…

Q: Q3/A solid circular shaft is subjected to a bending moment of 3000 N.m and a torque of 10000 N.m.…

Q: 2,2) There is an adiabatic turbine to which steam enters at 12.5 MPa and 773 K and leaves, after…

A: Given: Steam enters the turbine at 12.5 MPa and 773 K. At this pressure and temperature: From the…

Q: A car is initially at rest and starts to accelerate at a constant rate of 6 m/s2. What is the…

Q: b3 C Q ↑ D P= 23 KN R = 34 KN Square Bars b₁ = 57 mm 6₂ = 19mm b3 = 38mm WHAT IS THE AXAIL STRESS IN…

Q: Box of mass 10 kg resting on rough horizontal surface. Find friction force and normal force if…

Q: Q2/ In equilibrium position shown in figure below. The uniform bar (AB) has a mass of (50 kg) and…

Q: A mass M is under tension from wires CD and DE. If CD is 25º from the horizontal while DE is 30º…

A: The safe value of mass: m = 231.4068 kg

Question

Q2/ In equilibrium position shown in figure below. The uniform bar (AB) has a mass of (50 kg)
and supports the (200 kg) load at (A).Calculate the tension (T) in the cable and the force at (B)?
"i
2.5m
1200 kg
2.5m
л
()
|||

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
The simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 2,2 kN. Angle α = 39 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N2 in the rod 2, considering that N2>0 for tension and N2<0 for compression.
The simplest truss consists of two rods and is loaded by the force F. Given: F = 7 kN. Angle α = 50 degrees. Find: the algebraic (positive or negative) value (in kN) of normal force N2 in the rod 2, considering that N2>0 for tension and N2<0 for compression.
A uniform horizontal beam with a length of 1.7 m and a weight of 200 N is attached to a wall by a pin connection. Its far end is supported by a cable that makes an angle of 35.0° with the horizontal. If a crate of mass (M) 87 kg hanged 1.7 m from the wall, find the tension in the cable, as well as the magnitude and direction of the resultant force exerted by the wall on the beam.
Q)Two blocks A=150 N and B=? are connected by a rod at their ends by frictionless hinges as shown in the Fig. Find the weight of block B required for limiting equilibrium of the system, if µ = 0.35 at all sliding surfaces.
A bar AE is in equilibrium under the action of the five forces shown in Figure. Determine T, P, and R.
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
Two weights, A and C, are fixed to a bar, B. Their masses are: A = 60 kg, B = 230 kg,C = 45 kg. B is, in turn, connected to a fixed vertical post by a hinge and a support cableD. The geometry of the system is shown at right. Treat weights A and C as point masses a)What is the tension in support cable D? Be sure to include a detailed freebody diagram to accompany your analysis.b) What is the magnitude of the force provided by the hinge?c) What is the moment of inertia of the A + B + C as a rigid system, for rotationabout the hinge? For analysis, break the beam into a short piece to the left of thehinge, and a separate longer piece to the right of the hinge. If the support cable D on should break,d) what is the angular acceleration of the beam and weights at the moment the cable breaks?e) what is the magnitude of the linear acceleration experienced by each of the weights, A and C, at moment the cable breaks?
The pulley system shown in Figure Q1c lifts a mass,m,of 550 kg.Calculate the force FA necessary to maintain the suspended mass in static equilibrium; and determine the forces at the ceiling anchor points A and B. Assume frictionless and weightless pulleys and use g = 9.81 m/s2.