Q2: The pressure difference measured by the two tapping of a pitot-static tube, placed in the center of pipe line of diameter 40cm is 10cm of water the mean velocity in the pipe is 0.75 times the central velocity. Find the discharge through the pipe. Take co-efficient of pitot tube as 0.98.

Q2: The pressure difference measured by the two tapping of a pitot-static tube, placed in the center of pipe line of diameter 40cm is 10cm of water the mean velocity in the pipe is 0.75 times the central velocity. Find the discharge through the pipe. Take co-efficient of pitot tube as 0.98.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1. At 101.325 Kpa and 21°C, an industrial fan develops a brake power of 100KW and head of 120mm…

Q: A submersible pump deliver 350 gpm of water to a height of 5ft from the ground. the pump was…

A: Given data: Q=350 gpm Need to determine the pump power.

Q: fluid passing a boundary of a system is 80,000 ft-lb. Determine the exit pressure if the inlet…

Q: The diameter of pipe carrying water changes gradually from 20mm at A to 450mm at B. A is 4.57m lower…

A: Write the given data. dA=20 mmdB=450 mmzB-zA=4.57 m

Q: At a hydraulic plant, the difference in elevation between the surface of the water at intake and at…

Q: Q3: For ideal fluid, Find the force required to hold the blade in position, if the weight (1kN) and…

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

Q: For ideal fluid, Find the force required to hold the blade in position, if the weight (1kN) and…

A: Given: The weight of blade, W = 1 kN The discharge, Q = 0.4 m3/s

Q: A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill…

A: Given that, diameter of pipe= 14 cm =0.14m height of the hill from ground=…

Q: A pipe 800 m long connects two reservoirs whose level difference is 60 m. Find the discharge in pipe…

A: Length of pipe, L=800 mLevel difference between the two reservoirs, ∆z=60 mPipe diameter, d=0.5…

Q: A pitot tube directed into a water stream having velocity 2.3 m/sec. Its gauge difference of 30 cm…

A: It is a device used for the measuring of flow. The velocity of flow at a particular point is reduced…

Q: Q1\ Find the water discharge in 1/min for water flowing in a pipe and collected in a tank with…

Q: A gasoline pump fills a 80-L tank in 1 min 30 s. If the pump exit diameter is 4cm, what is the…

Q: QI/ For fig shown if water flow rate is 60 lit/s, Find (h) Note that Density: Pwater = 1 kg/m %3D 1…

A: Given:Q=60 L/sρwater=1 kg/m3ρair=1 kg/m3D1=500 mm =0.5 mD2=25 cm =0.025 m

Q: Inlet and throat diameters of a horizontal venturimeter are 250 mm and 100 mm respectively. The…

A: Inlet diameter, d1=250 mm=0.250 m Throat diameter, d2=100 mm =0.100 m Pressure at inlet, P1=15…

Q: A pump takes water at 60 F from a large reservoir and delivers it to the bottom of an open elevated…

Q: A fan is rated to deliver 680 m3/min at a static pressure of 304 cm of water when running at 219 rpm…

A: To find the power at the changed conditions

Q: Q3/ Hydraulic oil ISO 68 is flowing through a hydraulic line with an inside diameter of 1.4 inches…

Q: :-in the figure shown find the pump power if the discharge of oil is 200L/sec and the relative…

Q: A pitot tube directed into a water stream having velocity 2.3 m/sec. Its gauge difference of 30 cm…

A: Velocity of stream is given by the following formula, V=Cv✓2gh Where Cv=coefficient of velocity

Q: A fluid flows in a variable arca pipe with negligible viscous effects. At point 1, the pressure is…

Q: A pump with a shaft input of 8.62 kw and an efficiency of 72 % is connected in a water line carrying…

A: Given: The shaft input, W = 8.62 kW The efficiency of pump, η = 0.72 The volumetric flow rate, Q =…

Q: The water is flowing through a pipe having diameters 40 cm and 17 cm at sections land 2…

Q: 3. If a pump discharges 75 GPM of water whose specific weight is 61.5 lb/ft^3 (g=31.95 fps^2), find…

A: Given data, Q= 75 GPM (gal/min) Specific weight Y= 61.5 lb/ft3 , g= 31.96 ft/s2

Q: In oasis Water Company to purify the water, it is flowing through a reducer in a horizontal pipe…

Q: A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of…

A: Write the given values along with the suitable variables.

Q: total energy

Q: For the system shown below, calculate (a) the volume flow rate of water from the nozzle and (b) the…

A: (a) To find: The volume flow rate of water from the nozzle. Given: The diameter of nozzle is d=50…

Q: If a pump discharges 284 liters per minute of water whose density is 985 kg/m3; find a) the mass…

A: Given, Volumetric flow rate = Q˙ = 284 L/min = 284 x 10-3 m3/min Density of water = ρ = 985 kg/m3…

Q: A centrifugal pump is used to raise the water from the river to the reservoir, find: 1) total…

Q: Find the new GM if this tank is now pumped out till half empty is a ship of 9500 tonnes displacement…

A: Given that, W=9500 tonnes,KM=9 m,KG=8.5 ,Tank→15 m×10 m×2 m The mass of the water pumped out will…

Q: a. the total dynamic head in meters b. the water power in kW c. the motor horsepower if the pump…

Q: For fig shown if water flow rate is 60 lit/s, Find (h) Note that Density: Pwater = 1 kg/m Pair = 1…

Q: Estimate the pump power in kW delivered to the water.

A: Given: discharge= 220m^3/h friction head loss= 5 m To determine: Pump power

Q: Q3: In the orifice meter exper we found the following data of sample: The volume of water through 15…

A: Disclaimer :“Since you have posted a question with multiple sub-parts, we will solve first three…

Q: The power 491 W is required to transmit 3 x 103 m2/s of water. Find the loss of head due to friction…

Q: A gasoline pump fills a 80 L tank in 1 min 15 s. If the pump exit diameter is 4 cm, determine the…

A: Given Data Pump fill 80 liters in 1min 15 sec Calculate the discharge rate…

Q: A pipe of diameter 25 cm is suddenly enlarged to diameter of 50 cm. If pipe carries 350 lit/sec,…

Q: 3-Water flows through D=15 cm, At a velocity of V=2.5m/s. Find A-Volume flow rate. B-Mass flow rate.…

Q: A cylindrical pipe with water flowing downward at 0.03 m3/s having top diameter of 0.08, bottom…

Q: Water at 25°C is pumped at 1800 gal/min from the lower to upper reservoir, as shown in Figure below…

Q: 4. If a pump discharges 75 GPM of water whose specific weight is 61.5 Ib/ft^3 (g=31.95 fps^2), find…

Q: pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A: It is required to determine total energy head

Q: The diameter of a pipe at the larger end is 0.6 cm and at the smaller side is 0.3 cm the larger and…

Q: Q3: Water flows from reservoir A through pipe 1, diameter d, = 120 mm, length L=100 m, to junction D…

A: d1=120 mm L1=100 md2=75 mm ,L2=50 m d3=60 mm ,L3=30 mZA-ZB=12 mZA-ZC=20 m

Q: Q1: Find the pump efficiency if the pressure difference across the pump is 230 kPa. If the outlet…

A: Given: P2 - P1 = 230 kPa D2 = 7 cm = 0.07 m D1 = 14 cm = 0.14 m m = 50 kg/s Efficiency of motor =…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Q2: The pressure difference measured by
the two tapping of a pitot-static tube,
placed in the center of pipe line of
diameter 40cm is 10cm of water the mean
velocity in the pipe is 0.75 times the central
velocity. Find the discharge through the
pipe. Take co-efficient of pitot tube as 0.98.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If a pump requires a minimum of 2.75m of NPSH, how high (absolute value in meters) can the centerline of the pump be located above the top of an open tank that supplies a 27°C-water to the pump? The water tank is 1.83m high which is filled to the brim, and the total pipe friction is 0.70m.
A horizontal venturimeter with inlet diameter 20 cm and throat diameter 10 cm is used to measure the flow of water. The pressure at outlet is 14.715 N/em and the vacuum pressure at the throat is 40 cm of mercury. Find the discharge of water through venturimeter.
The inlet and throat diameters of a horizontal venturimeter are 30 cm and 10 cm respectively. The liquid flowing through the venturimeter is water. The Pressure intensity at inlet is 13.734 N/cm² while the vacuum pressure head at the throat is 37 cm of mercury. Find the rate of flow. Assume that 4% of the differential head is lost between the inlet and throat. Find also the value of Ca for the venturimeter.
Answer seems to be 736kpa, please show Formula and calculation as fast as (handwritten only) A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine at a rate of 200 L/s at the bottom of the water body. The pressure difference across the turbine is
A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. ( WITH FREE BODY DIAGRAM ) CHOIECES: A.2.56 B.-2.72 m C.12.74 m D.-4.67 m
A pump raises 650 tonnes of pure water a height of 55m in 6 hours. If the pump efficiency is 100%, what is the power required to drive the pump?
The suction diameter of 60 mm reads 2 psi vaccum and 50 mm diameter discharge with 250kpag. The suction water level is 5 m above water pump centerline and discharge water levelis 25 m above water pump centerline and discharge is 2 m. If discharge is 0.01 m^3/s, findthe horsepower needed to pump the water for 80 percent pump efficiency.
Show the solution. A fan has suction pressure of 5 cm water vacuum with air velocity of 5 m/s. The discharge has 20 cm water gage and discharge velocity of 10 m/s. Find the total head of the fan.
If you have a closed system that is filled with water on 2bar, the pump is selected for pressure losses due friction of the pipes(1bar) 1/ why don't we have to take pressure losses due height in account? 2/ what is the pressure at 100 m height inside the system? When the pump stops? And when the pump is circulating, prove your answer figure in image
Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside area of . The exit nozzle at point F has an inside area of . The distances are , , and , respectively. Find the pressure at point D_______ A. 5.74 kPa (gage) B. -5.74 kPa (gage) C. 5.74 kPa (absolute) D. -5.74 kPa (absolute)
Include a free body diagram A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. -4.67 m C. 2.56 D. -2.72 m
A pump was installed with a suction head of 6 meter and a discharge head of 10 meters. The discharge rate of the pump is 60 liters per minute. What is the water horsepower of the pump?