a. the total dynamic head in metersb. the water power in kWc. the motor horsepower if the pump efficiency is 66% 3. A pump 254mm suction pipe and a 127mm discharge pipe is used to deliver52L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gagelocated 100 cm above the suction gage which reads 108 kPa gage. Determine thefollowing:

Answered: Image /qna-images/answer/b78725b9-5916-4825-ae41-a5a8caf28b40.jpg

Answered: a. the total dynamic head in meters b.…

Engineering

Mechanical Engineering

a. the total dynamic head in meters b. the water power in kW c. the motor horsepower if the pump efficiency is 66%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The three primary dimensions mainly used in hydraulics are length, force and temperature. Both syste...

A: It is false that the three primary dimensions mainly used in hydraulics are length, force and temper...

Q: A Cold Store maintains a storage temperature minus 23°c in an ambient of 27°c. he pleent is fittes w...

Q: e called a

A: introduction: here we explain robotics and robot

Q: A 2 m wide, 3 m high, and 50 mm thick sheet of XPS insulation (M = 50 ng/Pa.s.m2), has a vapor press...

A: Given data,Length of Sheet=2mHeight=3mthickness=50mm=50×10-3m=5×10-2mDiffrence b/w vapour pressure =...

Q: A SDOF system with a mass 25 kg and stiffness 10 N/mm with damping 0.15 Ns/m is initially at rest. I...

A: given; initial velocity(u)=100mm/s =0.01m/svelocity(v)=?at time t=2sec ...

Q: A jet plane is launched from a catapult on an aircraft carrier. In 2.0 s it reaches a speed of 151 k...

Q: angle of bite in radians is??

A: Given; In a single pass rolling process using d=412 mmR=206 mmwidth,b=120mmthickness,t=8mmreduction,...

Q: Provide a complete and logical solution for the problem. If linear interpolation is required in the ...

A: (a) Write the given data. k=1.34rc=5V1=6 ft3P1=13.75 psiaT1=100 °FQin=340 BTU

Q: problem 2 You are required to design (select, optimize) the number of cables and cable diameter for ...

Q: A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN. I...

Q: 4m seawater (SG=D1.031) A 60°

A: Find the hydrostatic force on the gate

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

Q: 1. An AISI 1018 steel has a yield strength, Sy = 295 MPa. Using the distortion energy theory for the...

Q: Reneew If F - (1201 - determine the resultant moment produced by these forces about point O. Expross...

Q: The bar ABCD in Fig. (a) consists of three cylindrical steel segments with different lengths and cro...

Q: Calculate the theoretical fracture strength of a brittle material wherein fracture occurs by propaga...

A: As per given question Strss=1200mpa Crack=0.25mm Radius of curvature =1.25×10^3 mm We have find fra...

Q: 3) PARAMETRIC: Liquid octane (CaH18) at 298 K & 1 atm enters a well-insulated combustion chamber and...

Q: An angular velocity of 50 rad/s expressed is approximately .. (rpm =revolutions per minute) O 100r r...

A: Calculated rpm ( revolution per minute).

Q: What are the different characteristics of materials? Define each shortly

A: The characteristics of the materials are the mechanical, thermal, optical and electrical properties...

Q: The instrument of mass 50 kg is meant for impact on a surface. The impact velocity 10m/sec. Inside t...

A: Given data as per question mass=50 kgx0=vo=10 msk=5 Nmc=1 NsmMaximum dispalcement of instrument afte...

Q: For a fully developed flow of water in a pipe having diameter 10 cm, velocity 0.1 m/s and kinematic ...

Q: Stato the minimum diametor of glass tube to be immersed in water, for which capillary offects are to...

A: Given that, Rise in water level, h=2.98 mm, Surface tension of water, σ=0.073 N/m, Angle of contact,...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

Q: rad/sec and having 20 te sure angle is 20° and m. on at the centre of the sha

Q: What is the pressure outside of a tire if the gauge pressure reads 32 psi and the interior of the ti...

A: Given data, Gauge pressure of tire is Pg=32 psi Interior of tire pressure is Pabs=47 psi

Q: 500KN 750 KN For the truss shown , the cross-sectional area of each member is 1,200 mm?. 60 60 60 60...

A: NOTE:- As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost...

Q: Q1: Determine the Moment of Force F (100N) shown in fig. down about point (A) by 2 ways at leasti 05...

A: GIVEN DATA - A TROLLY GIVEN ACTED UPON BY FORCE F=100N WE HAVE TO FIND MOMENT ABOUT POINT A

Q: . A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4...

A: Here given data says that Hight ,= 30 m Diameter at bottom= 6 m Diameter at top = 4.5 m Wight of...

Q: Consider a nuclear power plant operating on the ideal Rankine cycle with steam as the working fluid....

Q: A flat bar of width b = 60mm and thickness t=10mm is loaded in tension by a force P. The bar is atta...

Q: An escalator in a shopping center is designed to move 30 people, 75 kg each, at a constant speed of ...

A: Assumptions: Air drag and friction are negligible. The average mass of each person is 75 kg. The...

Q: Q1: Determine the Moment of Force F (100N) shown in fig. down about point (A) by 2 ways at least? 05...

Q: 200 mm Gmm -4mm 400 8mm 102mm

Q: 1. 2 kg of air at 500 kPa, 80°C expands isentropically in a non-flow system until its volume doubles...

Q: An aluminum rod is rigidly attached between bronze rod and steel rod as shown. Axial loads are appli...

A: Given: The maximum value of stress in steel is σs=120 Mpa. The maximum value of stress in aluminum ...

Q: Part A Consider the shaded area in (Figure 1). Determine the moment of inertia of the area about the...

Q: A refrigerator with Freon 11 as the working fluid is considered. Given the data below, compute the m...

A: Given, T1 = -22oC from Table ; h1 = 385.32 kJ/kg s1 = 1.743 kJ/kg.K P2 = 1 MPa From steam table; s2 ...

Q: The state of stress at a point, for a body in place principal stress is 10 kPa, then the normal stre...

A: As per given question Normal stress =100kpa Shear Stress =50kpa We have to find minimum principal s...

Q: A window measures 36 inches x 50 inches and there are 20 of these windows in a structure. The U-fact...

A: Given: Window of size 36 inches x 50 inches A=1800 in2=1.161 m2 Number of windows, n=20 U=1.3 Btu/h...

Q: Assume that a 20mmØ rivet joins the plates that are each 110mm wide. The allowable stresses are 120 ...

Q: The structure shown supports a distributed load of 700 Ib/ft. Assume a - 4.1 ft b-1.0 ft. c-2.1 ft, ...

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape a...

A: Given Data: Length of the beam, L=16 ft

Q: 20 F. 30

Q: Calculate the rate of overall heat transfer coefficient for the tube heat exchanger with inner and o...

A: Given Data: The diameter of the tube, d=4 cm The thickness of the tube, t=1.5 mm

Q: Water in a piston/cylinder arrangement is at 150 psia and 900 °F, as shown in Fig. C. There are two ...

A: Given data, State 1:- When the piston is in upper stops Pressure at state 1, P1 = 150 psia Temperatu...

Q: 4. The steel water pipe has an inner diameter of 100 mm and wall thickness 5 mm. If the flow of wate...

Q: NOTE: ANSWER ALL QUISTIONS Q1) Answer the following questions. (C..-- 1- Explain the selection of en...

A: 1. 1. The selection of a specific material for a particular use depends on various factors like oper...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

Q: Part a) Determine the power in hp delivered by the motor when the elevator is moving down at a const...

Q: A simple ideal Rankine cycle which uses water as the working fluid operates its condenser at 40C and...

A: Calculated enthalpy at the turbine inlet in (kJ/kg).

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

a. the total dynamic head in meters

b. the water power in kW

c. the motor horsepower if the pump efficiency is 66%

3. A pump 254mm suction pipe and a 127mm discharge pipe is used to deliver
52L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gage
located 100 cm above the suction gage which reads 108 kPa gage. Determine the
following:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 58L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gage located 120 cm above the suction gage which reads 110 kPa gage. Determine: a. The total dynamic head (TDH) in meters b. The water power in kW c. The pump efficiency in % if the power supplied by the motor is 15hp
Water flows through a horizontal Venturi meter whose inlet diameter is 31 cm. and throat diameter is 19 cm. The pressure at the inlet is 755 kPa and at the throat is 550 kPa. Neglect head lost. Determine the velocity in the throat, in m/s. Round off to three decimal places.
Consider the incompressible flow of water through a divergent duct, where the inlet has a velocity & section area of 5 ft/s & 10 ft2. If the exit area is 5x the inlet area and the density of water is 62.4 lbm/ft3, solve for the pressure difference. (Please type answer no write by hend)
A pump is discharging 12 liters/sec of water through 10 cm diameter pipe. When the pressure on the discharge side of the pump is 700 kPa, what pressure can be expected in the discharge pipe at a point 540 m distant from the pump and 45 m higher in elevation. Use n = 0.015.
Pls. answer thank you! In Francis turbine, the pressure gage leading to the turbine casing reads 385 kpa and center of spiral casing is 3.5 m above the tailrace. If the velocity of water entering the turbine is 9 m/s, what is the net head of the turbine?
A certain 15-Kw pump running at 1600 rpm has an inlet diameter of 20cm and the discharge line is 12 cm in diameter. The output from th pump is 2800 liters/min of 20C and the centerline of the pump discharge is 1.5 meter above the centerline of the intake pipe. Determine the efficiency of pump. Please show complete solutions and formulas used. Show schematic diagram too.
A pump 260mm suction pipe and a 150mm discharge pipe is used to deliver 58L/s of water. The suction gage reads 140 mmHg vacuum and the discharge gage located 130 cm above the suction gage which reads 120 kPa gage. Determine: a. The total dynamic head (TDH) in meters
Water (density 1000 kg/m?) flows through an inclined pipe of unform diametar. The velocity. pressura and elevation at section A are V, = 3.2 mis, p, =186 kPa and 2, = 245 m respectively, and those at section B ara V = 3.2 /s, py = 260 kPa and 2y = 9.1 m, respectivoly. If accaleration due 1o gravity /s 10 m/s* then the head lost due to friction is ‘m (round off 1o one decimal place).
A jet of water, issuing from sharp-edged vertical orifice under a constant head of 60 cm , has the horizontal and vertical coordinates measured from vena contracta at a certain point as 10. cm and 0.45 cm respevtively. Find Cc if Cd= 0.60.include your free body diagrama.0.612 b.0.962 c.0.98 d.0.623
A pump was installed with a suction head of 6 meter and a discharge head of 10 meters. The discharge rate of the pump is 60 liters per minute. What is the water horsepower of the pump?
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 6.60 ft, r1 = 4.40 ft, b2 = 2.60 ft, and b1 = 7.20 ft. The runner blade angles are ?2 = 82° and ?1 = 46° at the turbine inlet and outlet, respectively. The runner rotates at n. = 120 rpm. The volume flow rate at design conditions is 4.70 ×106 gpm. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (hp) and required net head (ft).
1. A centrifugal pump with 30 cm impeller delivers 30 l/s against a head of 24 m when running at 1750 rpm. What will be the delivery of a homologous pump of 15 cm impeller diam eter assuming same efficiencies and speed? 2. A centrifugal pump with 2.3 diameter impeller running at 327 rpm delivers 7.9 m3/s of water. The head developed is 72.8 m. The width of the impeller at outlet is 0.22 m. If the overall efficiency is 91.7% determine the power to drive the pump.