Q2: The water in a tank is pressurized by air, and the pressure is measured by a multi fluid manometer as shown in the figure. Determine the air pressure in the tank if h1=0.1 m, h2=0.2 m, h3=0.35 m. Take the density of water, Oil and Mercury to be 1000, 850 and 13600 kg/m³, respectively, also atmospheric pressure is 85.6 kPa. Air Water hi h₂ mercury

Q2: The water in a tank is pressurized by air, and the pressure is measured by a multi fluid manometer as shown in the figure. Determine the air pressure in the tank if h1=0.1 m, h2=0.2 m, h3=0.35 m. Take the density of water, Oil and Mercury to be 1000, 850 and 13600 kg/m³, respectively, also atmospheric pressure is 85.6 kPa. Air Water hi h₂ mercury

Name: Q2: The water in a tank is pressurized by air, andthe pressure is mea
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2: The water in a tank is pressurized by air, andthe pressure is measured by a multi fluidmanometer as shown in the figure. Determine theair pressure in the tank if h1=0.1 m, h2=0.2 m,h3=0.35 m. Take the density of water, Oil andMercury to be 1000,

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The water in a tank is pressurized by air, and the pressure is measured by a multi-fluid manometer, as shown in the figure. Determine the gage pressure of air in the tank.
Consider a double-fluid manometer as shown in the figure, attached to an air tank. If one fluid is mercury, determine the density of the other fluid for the given pressure. Take Patm= 100 kPa.
Open tank (4.5 m long, 2.5 m height and 3 m wide) contains liquid (S-0.75) to height 1. m. If this tank is accelerated along its length on a horizontal truck at a constant value of 3.5 m/s, determine pressure at the bottom of the tank at front and rear edges (in kN/m). (take y=9.8 kN/m for water)
The open tank filled with a liquid in full as shown in the figure below has the height of h = 6.00 m. The inclined angle of the inclined wall is = 45.00 °. The width (perpendicular to the screen) of the inclined wall is w = 20.00 m. The specific weight of the liquid is = 9.81 kN/m3. (1) For the inclined wall, determine the average pressure on it._________ (kPa)
A gasoline line is connected to a pressure gage through a double-U manometer, as shown. If the reading of the pressure gage is 260 kPa, determine the gage pressure of the gasoline line. Assume the density of air to be 1.225 kg/m^3.
A tank of water 4 m deep receives a constant upwardacceleration a z . Determine ( a ) the gage pressure at the tankbottom if a z = 5 m 2 /s and ( b ) the value of a z that causes thegage pressure at the tank bottom to be 1 atm.
Pipe A contains gasoline (SG = 0.7), pipe B contains oil (SG = 0.9), and the manometer fluid is ,ercury. Determine the new differential reading if the pressure in pipe A is decreased 25 kPa, and the pressure in pipe B remains constant. The initial differential reading is 0.30 m. (Hydrostatic)
The water in a tank is pressurized by air, and the pressure is measured by a multi-fluid manometer. Determine the gage pressure of air in the tank
The liquid inside the tank on the left side of the 2000 mm wide rectangular shaped lid hinged from the O point, which is seen in the middle of the figure, is under pressure of -22.50 kPa, and on the right side there is oil with a density of d= 0.80. Find the intensity and direction of the force that will act on the O point in order for this cover to remain in balance (Y(liquid)=0.9 kg/lt, Ig=bh^3/12). (Hava=air, Sıvı=liquid, yağ=oil)
Water is stored in a tank with an inclined panel AB whose dimensions are 2m long by 1.6m wide. The manometer indicated a gage liquid height of z = 1.2m. (a) determine the pressure (in kPa) at B. (b)Determine the pressure (in kPa) at A? (c) Apply the pressure prism concept in determining the force (in kN) exerted on side AB. (d) At what distance from A (along the surface of panel AB) is the hydraulic force acting (in cm)?
The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as shown in Figure below. Analyse the change in manometric fluid (oil and mercury) with another fluid on manometric height h2 and h3 for the manometer given in figure above.