Q2. All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA 5k2 D2 VA VOUT 5k2 VB -2V D1B Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. CBA indicates the numbers in the last three digit of your student number. DIB(ON/OFF) D2(ON/OFF) | VOUT (sign and numerical value) VA VB DIA (ON/OFF) OV A OV B A

Q2. All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA 5k2 D2 VA VOUT 5k2 VB -2V D1B Indicate in the table whether the diodes D1A, D1B and D2 are ON/OFF with the given VA and VB values. Also give the corresponding VOUT numerical values. CBA indicates the numbers in the last three digit of your student number. DIB(ON/OFF) D2(ON/OFF) | VOUT (sign and numerical value) VA VB DIA (ON/OFF) OV A OV B A

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
In the circuit shown, determine the current flowing through the resistor R1. (Use 2nd approximation and assume all diodes are silicon for all the problems)
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
Calculate the total current of a circuit with a 9.5 V voltage source connected in series with a directly biased silicon diode and a series resistor of 440 Ω. Consider the second approximation of the diode where it is considered to be connected to a battery in series. Units of the response in milli amperes. Note: I put the original exercise in Spanish, so that it is better understood. Explain step by step, please.
Consider the circuit below,assuming the diode is ideal:1) When voltage source (Vin) provides a positive voltage, the diode isequivalent to ____________ circuit2) When voltage source (Vin) provides a negative voltage, the diode isequivalent to ____________ circuit3) Sketch the I-V characteristic of the ideal diode model on the chart below.
In the circuit shown, determine the circulating current. (Use 2nd approximation and assume all diodes are silicon for all the problems)
Q1: In this Zener diode regulator, the source voltage varies from 6 V to 14 V. Assume that the load current varies between 1 mA and 35 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Q2: Given the circuit design for a Zener diode regulator in the Ques 1, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
A 1N4733 zener diode has a Zz of 7 ohms. Considering the data of the manufacturer's hona, the Vz = 5.1 V with a test current, Iz, of 49 mA. What is the voltage across the zener terminals when the current is 65 mA? When the current is 25 mA? Include the graph where these values are shown.
A semiconductor junction diode, we can say that: a) The diode is composed of two types of crystal, one positive side (Anode) and the other P-type (Cathode) side, allowing the flow of charge from N to P.b) It is an electronic component that has two terminals, the Anode (with material of type N - Electrons) and Cathode (with material of type P - Gaps), which allows the flow of charge from P to N.c) It is the union of a P-type crystal and an N-type crystal, thus creating a PN junction, thus creating a simple solid-state device, the junction semiconductor diode.d) At a temperature of 25 degrees Celsius, the depletion barrier has a potential barrier, which for silicon is 0.7 volts and for germanium it is 0.3 volts.e) None of the above options is correct. Choose one of the alternatives
Analyze the ON/OFF states of all diodes (D1 and D2) inthis circuit, using the ideal-diode model.
A 0.5 W zener diode is rated to have VzT = 4 V at a test current of IzT =11.0 mA. Its incremental resistance r, = 68.0 Ohms. What voltage will result when conducting a reverse current of Iz = 21 mA? What is the maximum safe current, using the linearized model and including the effect of rz?
Answer the following questions according to the above. Remember Kirchhoff's laws when making your calculations in this question. a) According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply? b) According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply? c) Calculate how many values V?−?? are when the zener current is 0 mA. D) Calculate how much the value of ??−?? is when the zener current is at its maximum value.