For the full wave rectifier circuit shown, if Vs=15sin(120nt) (V), R=10o11, assuming constant voltage drop with VDo=0.7 J. 1. LDraw clearly and accurately with details the following waveforms: Source voltage (v3), load voltage (vo) 2. Describe in details the operation of the circuit indicating which diodes will be ON which ones will be OFF and state clearly the condition at which each diode will be ON or be OFF. 3. Calculate the mean load current (IRmean) given Vmean=2Vp/T. 4. Calculate the PIV. Da子 ac vo line Us voltage

For the full wave rectifier circuit shown, if Vs=15sin(120nt) (V), R=10o11, assuming constant voltage drop with VDo=0.7 J. 1. LDraw clearly and accurately with details the following waveforms: Source voltage (v3), load voltage (vo) 2. Describe in details the operation of the circuit indicating which diodes will be ON which ones will be OFF and state clearly the condition at which each diode will be ON or be OFF. 3. Calculate the mean load current (IRmean) given Vmean=2Vp/T. 4. Calculate the PIV. Da子 ac vo line Us voltage

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
1N4001, 1N4002, 1N4003, 1N4004, 1N4005, 1N4006 and 1N4007 For any of the diodes, describe with the aid of diagrams/illustrations its applications in an AC to DC Bridge rectifier power supply circuit. For your circuit show and describe how you are going to smooth out the ripple voltage that will be present.
Full-wave Bridge rectifier What is the effect of interchanging the probe connection to the resistor voltage waveform? What about, what is the effect of removing one diode from the circuit to the resistor voltage waveform?
) Determine the reading obtained withaDC voltmeter at RB when the switch is set at point B. b) Determine the reading at thesame RBusing ½ wave and Full wave rectifier AC meter respectively when the switch is set at point A. Given that Ifs = 100-µA and set at 10-V dc or rms range.
Plot the diode reverse characteristic, and estimate an approximate value for the reverse saturation current IS. From the results obtained in this experiment, compute the maximum power dissipated in the diode
For the circuit shown below, both diodes are identical with and the input voltage is . To analyze the circuit, we assume that both diodes are conducting (on). Is this correct? If yes, what is the value of ID1? If no, what are the correct diode states?
Two identical Schottky diodes are connected in series, one in the forward and the other in reverse direction, see figure. Assume the reverse saturation current, IS, of each diode to be known. Derive he current-voltage curve I(V) of this circuit. Plot it with the ratio I / IS on the y-axis and V / Vth on the x-axis. Make sure to cover a broad range of voltages, say, from –10 Vth to 10 Vth.
A full-wave bridge rectifier with a 236.86V p-p sinusoidal input has a load resister of 2KΩi. Draw the wave form that the load resistor R would see. ii. Assuming diodes are ideal, what is the dc voltage available at the load resistor? iii. What is the dc voltage available at the load if silicon diodes are employed? iv. Calculate the maximum current flow through the Diode D4 during conduction.
Why is the peak inverse voltage of a full rectifier 2Vs - Vo where Vs is the input? What is the purpose of this peak inverse voltage, as in what does it tell me about the diode?
(a)Derive the average and rms output voltages and currents for three-phase half controlled rectifier with free wheeling diode and RLE load.(b))In a single phase full converter, if output voltage has peak and average values of 325V and 133V respectively, find the firing angle.
a. For the circuit given in the figure on the right, set VRL to 10Find the maximum and minimum value range of RL and IL that will hold in volts.b. As a regulator, without damaging the diodethe maximum diode required to operateCalculate the power.
Can the regulator given in Figure Q4.b be used to regulate the output of a full-waverectifier, given the specifications for Io and Vpk in the Table 4 above? The rectifier voltage varies between 0.7Vpk and Vpk (that is, the ripple voltage is 30%of Vpk). The value of the Zener voltage Vz is 5.6 V, and the Zener diode power ratingis 2W. The regulator must supply to the load the current of at least Io mA. mA = 160 V = 22v To answer this question, you need to determine the value of the resistor R for theoutput requirements specification for Io and Vpk given in Table 4.