Q20. In an ideal Diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98 kN/m² and 60 °C, respectively. The maximum pressure attained during the cycle is 4.5 MN/m² and the heat received during the cycle is 580 kJ/kg of gas. Take y 1.4 and C, 0.717 kJ/kg K. Determine for the cycle:

Q20. In an ideal Diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98 kN/m² and 60 °C, respectively. The maximum pressure attained during the cycle is 4.5 MN/m² and the heat received during the cycle is 580 kJ/kg of gas. Take y 1.4 and C, 0.717 kJ/kg K. Determine for the cycle:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 90 kPa and 300 K, respectively. At the end of the heat addition, the pressure is 6821 kPa and the temperature is 1950 K. Determine the thermal efficiency of the cycle in %.
Show that the air standard efficiency of a gas turbine can be expressed in terms ofpressure ratio only.
A Diesel cycle has a compression ratio of 22 and begins its compression at 83 kPa and 15°C. The maximum cycle temperature is 1200°C. Utilize air-standard assumptions. The properties of air at room temperature are R = 0.287 kPa·m3/kg·K, cp = 1.005 kJ/kg·K, cv = 0.718 kJ/kg·K, and k = 1.4. Determine the thermal efficiency of this cycle using constant specific heats at room temperature. The thermal efficiency of this cycle (in decimal fraction)
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
A turboshaft engine comprising a gas generator and a free power turbine is selected to provide propulsive power for a helicopter. The helicopter is hovering in ISA conditions at an altitude of 4100 feet. The following data applies to this engine at this static max power operating point. Intake mass flow: 8.9 kg/s Compressor pressure ratio: 24.5 Compressor isentropic efficiency: 88% Mechanical efficiency: (HP & PT shaft) 99% Combustion chamber pressure loss Combustion chamber inlet pressure 4% Combustion efficiency 98.8% Combustion chamber exit temperature: 1585K Gas generator turbine isentropic efficiency: 92% Power turbine isentropic efficiency: 90% The effects of the intake and exhaust ducts may be ignored. It may be assumed that for: Air: Cp = 1.005 kJ/kg • K, y = 1.4, R = 0.287 kJ/kg • K Combustion gases: Cp = 1.148kJ/kg • K, y = 1.333, R = 0.287 kJ/kg • K A 6% direct bleed of air from the exit of the compressor is…
In a turbojet engine, what are the assumptions for static & stagnation temperatures and pressures for the stators and rotors in both the turbine and compressor thanks
The conditions at the beginning of compression in an Otto engine are 101.3 kPaa, 0.66 m^3 and 38.0 C. If the volume at the beginning of the isometric heat addition is 0.06 m^3, what is the percent clearance?
In an ideal diesel cycle the pressure and temperature at the beginning of the adiabatic compression are 98.5kN/m^3 and 60°c, respectively.themaximum pressure attained during the cycle is 4.5MN/m^3 and the heat received during the cycle is 580kJ/kg gas.Determine for the cycle a) the volume ratio of compression b) the temperature at the end of compression c) the temperature at the end of heat reception d) the temperature at the end of adiabatic expansion e) the net work done/kg of gas f) the thermal efficiency g) the work ratio h) the mean effective pressure I) the Carnot efficiency within the cycle temperature limits.
10 m3/min of free air is to be compressed to 8 bar gauge in two stages. Assuming a 2 bar gauge intercooler pressure and a polytropic index of 1.3, what is the power consumption of the second stage compressor ? Please choose correct option a. 27.76 KW b. 22/7/π m3/min c. 20.46 KW d. 20.46 bar-m3/min e. 48 HP
in regard to thrust-producing engines, what is the dilemma between performance versus efficiency, referencing the propulsion efficiency equation and does an increase in one result in a decrease in the other?
Design a steam power cycle that can achieve a cycle thermal efficiency of at least 40 percent under the conditions that all turbines have isentropic efficiencies of 83 percent and all pumps have isentropic efficiencies of 65 percent. please include (i) System figures and T-s diagrams with labelled states and temperature, pressure, enthalpy, and entropy information for your design. (ii) Sample calculations.
A gasoline engine that operates in an air-standard Otto cycle has a total displacement volume 0.95 ft3 running at 2250 RPM, and a clearance volume of 15%. A 715 BTU/lbm of heat is added at constant volume. The initial conditions of air prior to the compression are 80oF and 14.5 psia. COnsidering variations of heat at given temperatures, determine the maximum pressure and temperature in the cycle, the work net, the total power in hP, and the thermal efficiency of the cycle. Draw the P-V and T-S diagram.