Q2/B)- Show the connection of three combination op-amp stages ( Parallel and series connection) using an LM348 IC to provide outputs that are 110, 400, and 2601 times larger than the input. Use a feedback resistor of Rf = 500 k? in all stages, while can use only (R= 50 k? for first stage), (R= 25 k? for second stage), and (R= 10 k? for third stage

Q2/B)- Show the connection of three combination op-amp stages ( Parallel and series connection) using an LM348 IC to provide outputs that are 110, 400, and 2601 times larger than the input. Use a feedback resistor of Rf = 500 k? in all stages, while can use only (R= 50 k? for first stage), (R= 25 k? for second stage), and (R= 10 k? for third stage

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

1. A non-inverting op-amp circuit has the open loop gain of 105 and the resistances R1 = 1k Ω and R2 = 39k Ω . Calculate (a) The actual value of voltage gain, (b) Considering the finite open loop gain, the ideal value of gain, and (c) The percentage error, when ideal voltage gain is compared with actual voltage gain.
Q4/A)- Show the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? for third stage
Please answer this two part question A) It is known that when an Op-amp is operated using the negative feedbackconfiguration, the output impedance reduces. Derive an expression that proves this. B) It is known that when an Op-amp is operated using the positive feedbackconfiguration, the output impedance increase. Derive an expression that proves this.
A noninverting ampliﬁer is being designed to have a closed-loop gain of 36 dB. What op-amp gain is required to have the gain error less than 0.15 percent?
Which op-amp network is commonly used to reduce the effect of noise on comparator circuits (Schmitt trigger arrangement)?Using an output networkUsing a negative feedback networkUsing an input networkUsing a positive feedback network
A non-inverting op-amp circuit has the open loop gain of 104 and the resistances R1 = 2k Ω and R2 = 50 k Ω. Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain, and (c) The percentage error, when ideal voltage gain is compared with actual voltage gain.
An inverting op – amplifier stage is designed with an input resistance of 5 KΩ and feedback resistance of 10 KΩ. The load resistance is 100 Ω with DC gain of 5x10^4 . The output internal resistance is 500 Ω while the input impedance is infinity, assuming an input voltage of 1.5 volts, calculate the following ?a) The AC gain ?b) The output voltage ?c) The looking back resistance ?
A certain op-amp has three internal amplifier stages with midrange gains of 30 dB, 40 dB, and 20 dB. Each stage also has a critical frequency associated with it as follows: fc1 = 600 Hz, fc2 = 50 kHz, and fc3 = 200 kHz. (a) What is the midrange open-loop gain of the op-amp, expressed in dB? (b) What is the total phase shift through the amplifier, including inversion, when the signal frequency is 10 kHz?
What must the voltage at the inverting input of the op-amp be? What is the voltage drop across Rin? What is the input current, iin, through Rin? What is the output voltage vout?
Show the connection of three combination op-amp stages using an LM348 IC to provide outputs that are 110, 1681, and 420 times larger than the input. Use a feedback resistor of Rf = 400 k? in all stages, while can use only (R= 40 k? for first stage), (R= 10 k? for second stage), and (R= 20 k? fot third stage)
What are the nominal, minimum, and maximum values of the open-loop gain at 25◦C for an OP-27 operational ampliﬁer?
Question 3: Please write answers to all parts of the question in the separate dot points as shown What is the circuit called? Discuss all components including voltage sources. Which components determine the closed-loop gain of the circuit? Describe the slew-rate of the op-amp. Describe the Common-Mode-Rejection ratio of the op-amp? What is the unity gain bandwidth? Describe the gain bandwidth product (GBP). Describe the GBP relationship between the break (critical) frequency and the gain? What two methods calculate the max frequency? If one produces a higher value of maximum frequency than the other, which would you use as the maximum frequency?