Q2)For the systemshowninthefigure, the waterflowrateis(40)L/s. Find the30mpower transferredfrom the flow byCast iron pipeCast iron pipeL=46mL=60mtheturbine,d=6 ind=8 inK=3[v=1x10°m²/s].gate valveTurbine6 in.[Ans. 10.37kW]K=0.990° elbowTwo 8 in. 90° elbowsK=0.75 for each

To find :- Power transferred from the flow by the turbine.

Q2)For the system shown in the figure, the water flow rate is (40)L/s. Find the 30m power transferred Cast iron pipe from the flow by Cast iron pipe L=46m L=60m d=6 in the turbine, d=8 in K=3 [v=1x10°m?/s]. gate valve Turbine 6 in. [Ans. 10.37kW] K=0.9 90° elbow Two 8 in. 90° elbows K=0.75 for each

Q2)For the system shown in the figure, the water flow rate is (40)L/s. Find the 30m power transferred Cast iron pipe from the flow by Cast iron pipe L=46m L=60m d=6 in the turbine, d=8 in K=3 [v=1x10°m?/s]. gate valve Turbine 6 in. [Ans. 10.37kW] K=0.9 90° elbow Two 8 in. 90° elbows K=0.75 for each

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Airat1500kPaabsoluteflowsin25mm-diamtertube.Whatisthe maximum laminar flow rate. Use density of air=14.04kg/cu.m and ?=0.0000217Pa-s
Whatis the resistance coefficient, K, for a ball-type check valve placed in a2-in Schedule 40 steel pipe if oilis flowing at a velocity of 10 ft/s? A.3.60 B.2.85 C.4.43 D.1.90
A 2 1⁄2 - in. fire hose discharges water through a nozzle having a jet diameter of 0.97 in. the lost headin the nozzle is 5 percent of the velocity head in the jet. If the gage pressure at the base of the nozzle is 60 lb.per sq. in.: (a) compute the discharge in gallons per minute (1ft3 = 7.48gal); (b) what is the maximum horizontalrange to which the stream can be thrown (neglecting air resistance)? (c) what is the maximum possibletheoretical height that the jet can reach and at what angle?
water is flowing through a 35cm diameter welded steel pipe (f=0.014) of length 2300m that drains a reservoir under a head of 50m. the pipe has a thickness of 9mm. if the valve at the end of the pipe is closed in 9s. approximately what water-hammer a. 1.667MPa b. 1.567 MPa c. 1.467 MPa d. 1.367Mpa
Answer only that SECOND question thanks. Water is issued verAticalFly at the rate of 35462 L/Ts through a 61515 mTm diamDSeter noASDzzle. What is the the maxiSmum heighDSt of watSDr can reaDSch. The nozzle which furnished the water to a certain hydraulic turbine 280 mm in diameter and has a coefficient of velocity and discharge of 0.98 and 0.95 respectively. The nozzle supplied from 60 cm in diameter pipe in which water approached the nozzle with a total head of 335 m. Compute for the power in kN/s delivered by the jet to the turbine
For the 40 ° C water fl ow in Fig. P3.134, estimate the volumefl ow through the pipe, assuming no losses; then explainwhat is wrong with this seemingly innocent question. Ifthe actual fl ow rate is Q = 40 m 3 /h, compute ( a ) the headloss in ft and ( b ) the constriction diameter D that causescavitation, assuming that the throat divides the head lossequally and that changing the constriction causes no additionallosses.
4. Atube15mlongistoconnecttwolargetankswhosedifference in water level is 2m. The tube is to carry 5L/s of flow. What minimum size of tube is necessary to assure laminar flow condition?
Apipe through which water flowing is having Dia meter 30cm and 15 cm at Cross section 1, 2 respectiley. The velocity is water at section 1 4.5m/s.find kinetuc head at section 1,2 and Also rate of discharge
Pipe 1, 2, 3, 4 and 5 have lengths and diameters of 915m of 762mm, 610m of 300mm, 450mm of 250mm,760m of 380mm, and 1200m of 600mm. Pipes 2,3,and 4 are laid in parallel, both drawing from 1 and discharging into 5.If the discharge of pipe system is 10,000,000 gpd, what is total head loss from 1 to 5. Assume C = 100 for all pipes.
The energy loss between points 1 and 2 is 3.40 lb-ft/lb and the pump delivers 40 gal/min of fluid having a specific weight of 60.0 lb/ft3. What is the required hp of the pump? The inside diameter for the 2-in and 3-in schedule 40 steel pipes are 2.067 inches and 3.068 inches respectively
A tank 10 ft high, has theform of a frustum of a cone,with diameters of 8” at thetop and 4” at the bottom. Thetank is to be filled oremptied with water through anorifice at the bottom having acoefficient of discharge of0.60. What size of orificewill completely fill the tankin 6 minutes?
Theflowrateofwaterthroughacastironpipeis5000GPM.The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe