The energy loss between points 1 and 2 is 3.40 lb-ft/lb and the pump delivers 40 gal/min of fluid having a specific weight of 60.0 lb/ft3. What is the required hp of the pump? The inside diameter for the 2-in and 3-in schedule 40 steel pipes are 2.067 inches and 3.068 inches respectively

Q: NOTE (h in ft) h = 8.881 ft Problem II. A proposed elevated tank for a certain community has a…

A: Given  Unit weight of water= 62.4 lb/ft3  Height of tank = 120 inches

Q: Two pipes, A and B, are connected to an open water tank having a surface area of 1000 m². The water…

A: (b) is the correct answer.  Make any assumption(either leaving or entering) then apply the…

Q: m/N of oil flowing, calculate the power delivered Suction pipe is 1.4 N-m/N of oil flowing,…

A: Given:- 840 L/min crude oil sg=0.85 total energy loss=4.2N-m/N To find:- pressure at the pump level…

Q: 3 5-63. A 25-ft-long garden hose with ain. inside diameter, is used to drain a swimming pool, as…

A:

Q: Water is being discharged from a reservoir through a turbine as shown. Determine the elevation of…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: 1. Water is being pumped from the lower reservoir to the upper reservoir. Find the pump horsepower…

A:

Q: A proposed elevated tank for a certain community has a diameter of 72 inches and a height of 120…

A:

Q: Water flows downward through a vertical 10-mm- diameter galvanized iron pipe with an m average…

A:

Q: At what distance should a 500mm diameter cast iron pump be placed if an oil (oil density =…

A: We know hf=flv22gdPρg=flv22gdv=QA=0.095m3sπ40.52=0.48383ms-1

Q: 6. A galvanized iron pipe is required to carry water at a discharge of 3.5 cfs and with a head loss…

A:

Q: What is the head that must be supplied by the pump to the water to pump 0.4 m³/s from the lower to…

A: step 1-

Q: Water flows under a sluice gate on a horizontal bed at the inlet to a flume. The water depths at the…

A:

Q: If the flow of 0.10 m3/s of water (mu = 1.31 x 10-3 Pa.s) is to be maintained in the system shown,…

A: Using Bernoulli equation at point 1 and 2 P1γ + V212g + Z1 +Hp = P2γ + V222g + Z2 +HL P1 = P2 =…

Q: Q3. Water flows from the reservoir through a pipe and then discharge from a nozzle as shown. To…

A: Question is based on the water flow pipe system through a reservoir. Discharge through pipe,…

Q: Water is pumped thru a vertical 50mm new galvanized-iron pipe to an elevated tank on the roof of a…

A:

Q: What is the head that must be supplied by the pump to the water to pump 0.4 m/s from the lower to…

A: To Determine the head that must be supplied by the pump to the water to pump 0.4 m ^ 3 / s from the…

Q: Q-10: The diameters of the impeller of a centrifugal pump at inlet and outlet are 20 cm and 40 cm…

A:

Q: Q2: For the system shown below, find the minimum flow rate of the jet from the orifice at the end of…

A:

Q: Pipe in Series: Consider the two reservoirs show in below figure, connected by a single pipe that…

A: Z1-Z2= 9 mD1= 200 mmD2= 250 mmL1= 15 mL2= 45 mKLen= 0.5KLex= 1f= 0.01

Q: Q. No 5). A horizontal galvanized rectangular iron pipe (20x 50 cm) is supplying water with flowrate…

A:

Q: A 12-inch diameter pipe 9200 ft long (f = 0.024) discharges freely into the air at an elevation 18…

A: To find:  The percent increase in flow if a pump was added with a pump curve given by: hp = 70 - 5Q2

Q: A 10 ft by 15 ft rectangular cistern (storage tank for rainwater) has its top 30 ft below ground…

A: Given, Tank dimensions = 10 ft x 15 ft x 30 ft  Unit weight (γ) = 62.4 pcf

Q: Q3- Water flows downward through a vertical 10-mm-diameter galvanized iron pipe with a Reynold No.…

A: given diameter=10mm reynolds no=100000 we consider as pressure is constant at inlet and outlet

Q: The pump shown adds 1.6 horsepower to the water when the flow rate is 0.6 ft°/s. Determine the (a)…

A:

Q: Include a free body diagram. A pump draws water from a sump through a vertical 6′′ pipe. The pump…

A:

Q: What is the required shaft power (kW) that must be supplied to pump water at flow rate 0.010 m /s…

A: Given Q = 0.01 m3/s z1 = 10 m z2 = 45 m  f = 0.04 L = 100 m  D = 50 mm Efficiency of pump = 44%

Q: Water is pumped through a vertical 2-in new galvanized -iron pipe to an elevated tank on the roof of…

A:

Q: alculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min…

A: Solution: Given Data: The water flow rate, Q=30US gallon/minThe pressure above water level, P=40…

Q: A water discharge 8 m3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the…

A:

Q: Water (20°C) flows steadily through the piping junction in figure entering section 1 at 1.25 L/s.…

A:

Q: Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min…

A:

Q: The discharge through pump is 10 m³/sec and the total head is 100 ft. so calculate the unit power of…

A: Given: The discharge through the pump is 10 m3/sec. The total head is 100 ft.

Q: The parallel galvanized-iron pipe system delivers water with a total flow rate of 0.036 m3/s. If the…

A: To find discharge in pipe 1 and 2

Q: Q2: For the system shown below, find the minimum flow rate of the jet from the orifice at the end of…

A: Given that,   Z1 from 0 t0 10 m Z2 from 0 t0 9 m CV=0.85

Q: The tank in figure 3, contains water at 10°C and has a level of h = 15 feet, the pipe consists of…

A:

Q: 10.55 Water (60°F) is pumped from a reservoir to a large, pressurized tank as shown. The steel pipe…

A: Calculate the velocity through the pipe:V=QAQ= 1 ft3/sA=π4D2=π44122=0.0873 ft2V=QA=10.0873=11.459…

Q: Three pipes 1, 2, 3 are connected as shown. If the total discharge for the system is 610 L/s and the…

A: To find discharge in pipe 2

Q: Pipe 1,2,3 and 4 have lengths of 3000ft, 2000ft, 2400 and 1500, all being new cast iron. Pipes 2 and…

A:

Q: Pipes 1, 2 and 3 are 300 m, 150 m and 250 m long and 25 cm, 12 cm and 20 cm diameter with f1, f2,…

A:

Q: A centrifugal pump having an internal and external diameter of impeller 150 mm and 450 mm,…

A: The manometric efficiency of a centrifugal pump is defined as the ratio of the manometric head to…

Q: A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter…

A: Given data in question  Pressure  Depth of water Diameter  To find out  Discharge

Q: What is the head that must be supplied by the pump to the water to pump 0.4 m³/s from the lower to…

A:

Q: A water discharge 8 m³/s is to flow through this horizontal pipe, which is 1 m in diameter. If the…

A: Given: Discharge, Q=8 m3/s Diameter of the pipe, d=1 m Head loss, hL=7V22g

Q: For the branching pipe shown in figure . compute the discharge for pipes 1, and 3. D1=0.25m,…

A: Given data in question  Elevations of all 3 reserviors Friction constant values Length of pipes…

Q: Pipes 1, 2 and 3 are 300 m of 30cm diameter, 150m of 20cm diameter and 250m of 25cm diameter,…

A:

Q: 7. Given the following total heads H1= 8 ft and H2-106 ft and Q= 10cfs, calculate the head needed to…

A: As per bartleby policy i can answer only one question at a time. Please upload again other…

Friction

Friction is defined as the force that prevents any solid surface, any layer of fluid, or any kind of element or material from sliding.