Q3/ A multi plate clutches an included angle of 120°. A multi plate clutch, has 2 discs on the driving shaft and1 on the drive shaft, the outer radius is 100 cm and inside diameters 600 mm. The maximum intensity of pressure at any point is 0.2 N mm. If the is 0.25, determine the speed of the clutch if the power generated = 31582.807 kW. %3D Use both the uniform wear theory and the uniform pressure theory

Q3/ A multi plate clutches an included angle of 120°. A multi plate clutch, has 2 discs on the driving shaft and1 on the drive shaft, the outer radius is 100 cm and inside diameters 600 mm. The maximum intensity of pressure at any point is 0.2 N mm. If the is 0.25, determine the speed of the clutch if the power generated = 31582.807 kW. %3D Use both the uniform wear theory and the uniform pressure theory

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.
Determine the size of the clutch plate suitable for an Ambassador car employing asingle plate type friction clutch and developing 37.5 kW at 4282 rpm. The insidediameter of the clutch plate is 0.6 times its outside diameter and it is to be ensured thateven after a loss of 30% of the engine torque due to wear of the clutch facing, the clutchdoesn’t slip. The intensity of the pressure on the facing is not to exceed 70 kPa. Assumeµ = 0.3.
A conical Clutch transmits rotation from one rotating shaft to another though frictional forces on the conical face. The following data is for a conical clutchInside Diameter 25.0 mmOutside Diameter 100 mmCoefficient of Friction 0.33Axial Force 1000NIncluded angle 100 degreeRotational speed 1500rev/minuteCalculate the Torque and Power that can be transmitted without slipping using both Uniform Pressure Theory and Uniform Wear Theory
A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch. Subject: Theory of Machines
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.3; working speed= 600 rpm; friction surface number= 2; If required clamping force = 2917 N, clutch outer diameter = 400 mm, clutch inner diameter = 160 mm, what is the transmitted power?
A single disc clutch with both sides effective is required for a vehicle. The power for initial estimation of the clutch is 100 kW at 4000 rpm. Determine the radial dimensions (inner and outer radius) and the actuating force (W). Base the design on the uniform wear assumption. Assume maximum pressure (pmax) as 1.6 MN/m2 and ?2?1= 1√2where ‘r2’ and ‘r1’ represent inner and outer radius of the friction surface. Take µ = 0.35. Find also the minimum pressure (pmin).
The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum pressure under working conditions is 220kPa only. The clutch is used to connect two 25mm solid shafts with allowable shearing stress of 69 MPa. The inner and outer diameter of the clutch face is 60 mm and 120mm, respectively. What is the power in kW transmitted at 1000 rpm?
3) A multiple disc clutch, steel on bronze, is to transmit 7 kW at 1000 rpm. The inner radius of thecontact is 50 mm and outer radius of the contact is 75 mm. The clutch operates in oil with an expected coefficient of "0.1". The average allowable pressure is 0.35 N/mm2. Determine the total number of steel and bronze discs.
A single disc clutch is used to transmit 12kW power at 1000rpm. The axial pressure is limited to 0.08 N/mm2. If the external diameter of the friction lining is 1.25 times the internal diameter, find the required dimensions of the friction lining. Assume uniform wear conditions. The coefficient of friction may be taken as 0.3.
A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.
A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces has worn away by 1.25 mm. find the maximum power that can be transmitted assuming uniform wear. A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces…
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.