6. Determine the size of a piston rod subjected to a total load of having cyclic fluctuations from 15 kN in compression to 25 kN in tension. The endurance limit is 360 MPa and yield strength is 400 MPa. Take impact factor= 1.25, factor of safety= 1.5, surface finish factor= 0.88 and stress concentration factor = 2.25. [Ans. 35.3 mm]

6. Determine the size of a piston rod subjected to a total load of having cyclic fluctuations from 15 kN in compression to 25 kN in tension. The endurance limit is 360 MPa and yield strength is 400 MPa. Take impact factor= 1.25, factor of safety= 1.5, surface finish factor= 0.88 and stress concentration factor = 2.25. [Ans. 35.3 mm]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

MECHANICAL VIBRATION 6.10
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
engineering tolerance: A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journalbearing require rigidity and alignment with an accuracy of the location. Consider a journal bearinginlet diameter as the basic size. determine 1. the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter2. the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter
pleassssse solve question 9, statics
PROBLEM: 5 A helical valve spring is to be designed for an operating load range of 90N to 195N. The maximum deflection of the spring for this load range is 7.5 mm. Assuming a spring index of 9, a permissible shear stress of 550 N/mm2 for the material and the modulus of rigidity of 0.85x105 N/mm2. Determine the dimensions of the spring. (i.e. Diameter of the spring wire ,Mean coil diameter, Outer diameter of the spring, number of active turn and free length of the spring). Assume the spring coil is squared and ground.
Draw the complete FBD of members AB, FG, EBH and GHI parameters are attached in case needed.
Q 2. A journal bearing has a shaft diameter of 75.00 mm with a unilateral tolerance of −0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 700 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 30, SAE 40 and SAE 50 lubricants operating at an average film temperature of 60 °C.
A spur gear wheel will be produced for the movement mechanism driven by the electric motor of a crane system. Calculate the modulus in millimeters according to the root strength, taking into account the following data. Module width ratio =10, number of teeth=18, Clutch ratio(not clutch factor)= 1.5 , form factor Kf=1, operating factor Ki=1, load distribution factor Km=1, speed factor Kv=1, Driving electric motor Its power is P=1917 kW and the speed of the gear is n=48 rpm. Safety stress of gear material=322 N/mm2.
Data:P = 2 kipd = 3.6 inchw = 305 millimeterst = 0.03 meterr = 5.08 centimeterh = 0.6667 feet a) Calculate the maximum static stress in the material (in MPa). b) Estimate the theoretical stress concentration factor at the fillet c) Estimate the theoretical stress concentration factor at the hole
A hydraulic cylinder with a bore radius of 100 mm and an outer radius of 200 mmhas been designed to withstand a maximum internal pressure of 200 MPa inservice. During operation, the pressure within the cylinder is retained by a freelysliding piston. The steel used in the manufacture has Young’s modulus of 210GNm-2. In an alternative design, the cylinder has been constructed as a compoundcylinder (duplex cylinder) with the same bore and outer radii by shrink-fitting twotubes of the same steel. The nominal radius at the common interface is 150 mmand the radial interference (shrinkage allowance, δ) is 100 μm (micro-meters).a) Determine using Lame’s equations, the radial and circumferentialstresses at the cylinder bore, common interface, and outer surface.b) Graphically present (sketch) the variation of each of these stresses acrossthe cylinder wall, clearly indicating the values at the inner and outer surfacesof each cylinder.c) Draw the Mohr's circles representing the stresses acting on…
You are asked to design a plain surface journal bearing to carry a steady radial load of 5.75 kN while the shaft rotates at 950 rpm. The shaft stress analysis determines that an acceptable nominal diameter of the journal is 62.5-mm and an l/d ratio is 1. The shaft is part of a machine requiring good precision. So a minimum radial clearance cmin= 0.040 mm seems appropriate. We shall use SAE 30 oil as a lubricant, at an inlet temperature of 45 oC. Analyze the hypothetical bearing,a) Determine the operating temperature Tave, and operating viscosity μave. b) Determine the minimum film thickness, ho, temperature rise of the lubricant, ΔTC, the total oil flow, Q, and side flow Qs in [mm3/s], the maximum film pressure Pmaxdeveloped in [MPa]. c) Determine the power loss, Hloss in [W], friction torque, Tf in [N-m] d) For minimum radial clearances, perform a design assessment using Trumpler’s criteria.
Subject:statics of rigid bodiesshow your solution please