Q3) A pipe of 10 km length and connects tow reservoirs having a difference of water level 25 m. If an additional pipe of same diameter and length 4 km is attached to the last 4 km parallel for the remainder length of 4 km to the lower reservoir as shown in Fig.2 below. What should be diameter of the pipe so that the velocity is 1.25 m/s in pipe (1). Take the friction factor 4f = 0.03. 1 25 m 6 km V, - 1.25 m/s 2 km IC

Q3) A pipe of 10 km length and connects tow reservoirs having a difference of water level 25 m. If an additional pipe of same diameter and length 4 km is attached to the last 4 km parallel for the remainder length of 4 km to the lower reservoir as shown in Fig.2 below. What should be diameter of the pipe so that the velocity is 1.25 m/s in pipe (1). Take the friction factor 4f = 0.03. 1 25 m 6 km V, - 1.25 m/s 2 km IC

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water enters and leaves the 6-cm-diameter pipe bend inFig. P3.45 at an average velocity of 8.5 m/s. The horizontalforce to support the bend against momentum change is300 N. Find ( a ) the angle ϕ ; and ( b ) the vertical force onthe bend.
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
Water is flowing from a garden hose . A child places his thumb to cover most of the hose outlet, causing a thin jet of high-speed water to emerge. The pressure in the hose just upstream of his thumb is 400 kPa. If the hose is held upward, what is the maximum height that the jet could achieveve?
Water is flowing through a pipe of 0.60-meter diameter and 2-kilometer length. If the average velocity of water is 2 m/s, what is the loss of head due to friction considering that the friction factor is 0.005?
If a jet is inclined upward 30O from the horizontal, what must be itsvelocity to reach over a 3-m wall at a horizontal distance of 18 m,neglecting friction?
Water (density 1000 kg/m?) flows through an inclined pipe of unform diametar. The velocity. pressura and elevation at section A are V, = 3.2 mis, p, =186 kPa and 2, = 245 m respectively, and those at section B ara V = 3.2 /s, py = 260 kPa and 2y = 9.1 m, respectivoly. If accaleration due 1o gravity /s 10 m/s* then the head lost due to friction is ‘m (round off 1o one decimal place).
The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
A horizontal 12-in pipe contracts to a 6-in diameter. The flow is 4.5 ft3 /s ofoil, s.g. = 0.83. If the pressure in the larger pipe is 42 psi and the pressure in thesmaller pipe is 38 psi, what resultant force is exerted on the contraction? Reportthe answer in lbs.
Water flows from the faucet on the first floor of the building shown in Fig. P3.6.4 with a maximum velocity of 20 ft/s. For steady inviscid flow, determine the maximum water velocity from the basement faucet and from the faucet on the second floor (assume each floor is 12 ft tall).
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
O1: A stream of water of diameter d = 0.1 m flows steadily from a tank of diameter D= 1.0 m. Determine The Weight Flowrate, needed from the inflow pipe if the water depth remains constant, 0 — d=010m
A vertical pipe of 1 m diameter and 20 m length has a pressure head of 5 m of oil at the upper end. When oil flows through the pipe at an average velocity of 4.5 m/s, the head loss due to friction is 1.6 m of oil. The density of oil is 880 kg/m3 Find the pressure at the lower end of the pipe, when the oil flow is (a) upward direction, (b) downward and also draw the neat sketch. i) Pressure at lower end when flow of oil is upward =________________ N/m2 ii) Pressure at lower end when flow of oil is downward =________________ N/m2