Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b Find the appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in). F 2,

Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b Find the appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in). F 2,

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter4: Shielded Metal Arc Welding Of Plate

Section: Chapter Questions

Problem 25R: Can a tee weld be strong if the welds on both sides do not have deep penetration? Why or why not?

See similar textbooks

Related questions

Q: The 20-N horizontal force acts on the handle of the socket wrench. What is the moment of this force…

Q: A close-coiled helical spring undergoes a static deflection of 30 mm when a mass of 2.5 kg is placed…

Q: Determine the moment of inertia of the shaded area with respect to the centroid (lx, ly = ?) 3 cm 8…

A: to find the moment of inertia of the shaded region.

Q: A centrifugal pump uses a 134767 rpm motor to pump 116334 kg/min of standard temperature water and…

Q: A steel rod 22 mm in diameter and 1000 mm long is required to have an elastic strain energy of 90…

Q: Which failure theory would be appropriate to solve the following problem: A rotating shaft is…

A: Given:A rotating shaft is supported by bearings at each end. The shaft supports a single load in the…

Q: Problem 4 Rod ABC is bent in the shape of an arc of circle of radius R. Knowing the 0= 43.6°, and P=…

A: Given- theta=43.6 degree p=100 lbDetermine- (a) reaction at B (c)…

Q: If the inlet diameter of the holding tank is 35cm and the outlet diameter is 30cm and the diameter…

Q: -b Fm A C W X ¦Y

Q: Determine the angle for equilibrium.

A: Given DataThe mass of the disk m =12KgThe weight of the disk W=m*g=12*9.81=117.72NThe unstretched…

Q: what value of the angle 8 will the water land closest to the

A: Given DataThe speed of the water V0=38.2 ft/sFinda) What value of the angle will the water land…

Q: The design of a camshaft-drive system of a four-cylinder automobile engine is shown. As the engine…

Q: Calculate the magnitude of the resultant force on the indicated area and its location NOTE: THE GATE…

A: Given:The specific weight of the Oil is .The diameter is .Consider free body diagram:

Q: Calculate the horizontal and vertical components of the hydrostatic thrust on the 90 cm radius…

A: Radius of cylindrical cover = 90 cm = 0.9 mγwater = 9.810 kN/m³θ = 90°h = 1.20 md = 3m

Q: A 3-phase, 318-V, 50-Hz, 35 HP, 6-pole, Y-connected induction motor is operating with a line current…

Q: In a factory, a wide brass plate with a uniform initial temperature of 25°C and a thickness of 3 cm…

A: The final temperature of the plate.Given:The initial temperature of the plate is .The surroundings'…

Q: Determine the ongular accelerations of the bors, if the system is released from the figure shown.…

A: Given:To find:Angular velocity of the bars

Q: behaviour of the iron sheet material under a sudden impact

A: The behavior of iron sheet material when subjected to a sudden impact depends on several factors…

Q: A uniform supersonic airstream travelling at a Mach number of 9.0 passes over a concave corner, as…

A: Mach number,M1=9.0shock angle,Assume,Deviation angle be

Q: Determine the deflection of point B

A: Given DataPortion AB made of steelThe Youngs modulus of the steel The Coefficient of thermal…

Q: 10.Given F = xy i-y²j find the work done in moving an object along paths C₁ and C₂ in the figure…

A: The work done in moving an object along a certain path can be calculated as;Path C1:Along the line…

Q: Up= 3.23 m S

Q: Air at 15°C and 100 kPa occupies 0.03 m³. The air is heated at constant volume until the pressure is…

Q: The variation of pump head, efficiency, and required ENPY parameters with flow rate obtained from…

Q: A ramjet drives a missile at V0=966m/s at an altitude of 33.5km (air density 0.01kg/m3 and T0=232K).…

A: The missile speed, Vo = 966 m/sThe density of air = 0.01 kg/m^3The temperature, To = 232 KThe…

Q: W B A Y Fj FM

Q: Problem 5.30 In (Figure 1), d= 70 mm and R = 400 mm Figure x B R 1 of 1 > Part A Determine the…

A: Distance d= 70mmRadius = 400mmMass = 70kg Find the minimum force and angle

Q: A turbo-generator has a combined steam rate of 5.35 kg/kW-hr at its rated output of 20 MW. The…

A: Given:Combined steam rate =5.35 kg/kwhTotal power output =20000 KWSteam inlet pressure = P1=17…

Q: A Carnot engine receives 120 BTU of heat form a hot reservoir at 664 °F and rejects 51 BTU of heat.…

A: Heat input (Qh) = 120 BTUHeat output (Qc) = 51 BTUTemperature of the hot reservoir (Th) = 664 °Fto…

Q: Determine the value of item (f)

A: Given DataThe power of the motor P = 200 hpThe speed of the motor N = 540 rpmAt Gear AThe diametral…

Q: What are the key advantages and disadvantages of using composite materials in mechanical engineering…

A: Composite materials refer to materials made from two or more constituent materials with…

Q: X A 4 M L₂ B B L3 LA Ls Y C Pipe ABC is supported by three smooth journal bearings, Find the…

A: Given information: F=480lbsM=180 lb-ftangle =45 degree.

Q: Determine the minimum coefficient of static

A: Given Data The mass of the car m= 1400 kg=1400*9.81=13734NFind Outa) The minimum coefficient of…

Q: Question #1: Determine the shear, axial, and bending moment distributions for the loaded beam shown…

A: Calculate and plot shear axial and bending moment distributions

Q: The figure shows a uniform rod OAB with a mass of 5 kg/m supported by a ball-and-socket joint at O…

Q: F1=55 lb Calculated the forces in members DC, HC, and HI using method of section determine whether…

Q: The design of a camshaft-drive system of a four-cylinder automobile engine is shown. As the engine…

Q: Water with a bulk temperature of 70 F flows through a 2-inch chart 80 steel pipe. The temperature of…

A: The bulk temperature, T = 70 F = 294.26 KThe diameter of pipe, d = 2 inThe steam temperature, Ts =…

Q: Which one is not one type of surfaces of discontinuity? a.Far field boundary b.Mixing layers…

A: This question is based on the concept of fluid mechanics.

Q: Calculate the centroid of the composite shape AB= 85 C=1 BC = 12

A: The centroid of the composite shape.Given:The shape is shown below.

Q: Consider the system shown in (Figure 1). Figure 1 of 1 Part A Determine the moment of the force F…

A: Given F=80 lb Positions of the points. Required: Moment of the force about A.

Q: Two rods are connected to the roof. All joints are hinged. AC = BC = 1 m. Load 'F KN' is acting in…

Q: The pin-connected structure, shown in Figure 1, consists of a rigid beam ABCD and two supporting…

Q: 100 mm T=? 45° 300 mm 400 mm O 250 mm The mechanism shown in the figure is in static equilibrium.…

A: In the above diagram, is angle of BC with horizontal and is angle of CD with horizontal.

Q: In a fixed volume, 0.3 m³ container, initially there is refrigerant R-134a at 6 °C. Initially, 60%…

Q: A 2 4 M F B L₂ L Y C 4 Pipe ABC is supported by three smooth journal bearings, Find the reactions at…

A: Applied force F = 480 lbsApplied moment M = 180 lb-ftAngle of the applied force , θ = 45°Lengths: L1…

Q: Consider a 15 μm fuel droplet traveling at 200 m/s relative to the surrounding air. The fuel density…

Q: The rectangular bar is connected to the support bracket with a 17-mm diameter pin. The bar width is…

A: Diameter of the pin: 17 mmWidth of the rectangular bar: w = 85 mmThickness of the rectangular bar:…

Q: Determine the moment of inertia of the shaded area with respect to the centroid (lx, ly =?) 3 cm 8…

A: To Find-The moment of inertia of the shaded area with respect to the centroid (lx, ly=?)

Q: Use backward-difference formula to evaluate the first derivative of y = x2 + 4x – 5 at x=0 using a…

Question

appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress value is (60ksi) and the size of the weld is (1/4in).

Q3 (a) What are the methods used to obtain a good weld when welding steel when the carbon content is high? b Find the
appropriate length of the weld joint shown in the figure if the force is equal to (60000lb) and the operating stress
value is (60ksi) and the size of the weld is (1/4in).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: The method for welding for high carbon steel

VIEW

Step 3: Weld length calculation

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A bracket is as shown in figure 2. Determine the uniform weld size for the arrangement. The permissible shear stress of weld material is 80 MPa. Consider the loading condition as shown in figure.
Assume that two 1.5-mm thick steel sheets are being spot welded at a current of 4000 A and current-flow time is 0.3 s. Using electrodes 5 mm in diameter, estimate the amount of heat generated and the amount of heat required to melt the weld nugget. Use an effective resistance of 350 un. Take u= 9,7 Joule/mm Which one of the following are correct? O a. If the electrodes were 7 mm diameter, the amount of heat generated would decrease b. The amount of heat generated by the equipment is between 1600 to 1700 Joules c. The equipment has enough power to weld the steel sheets. d. The equipment does not have enough power to weld the steel sheets e. The amount of heat required is between 700 and 750 Joules
I need right solution with clear calculations. Two steel plates having yield point stress of 350 N/mm2 are joined together by double fillet welds of 10 mm thick as shown in figure. The weldment is from the same parent plate material. If the weld has to be replaced by 3 bolts of the same material, one each at A and B and one at mid-way between C and D, design the bolts. Take factor of safety as 2 for the bolts
A GTAW operation is performed on low carbon steel, whose unit melting energy is 10.3 J/mm3. The welding voltage is 22 volts and the current is 135 amps. The heat transfer factor is 0.7 and the melting factor is 0.65. If filler metal wire of 3.5 mm diameter is added to the operation, the final weld bead is composed of 60% volume of filler and 40% volume base metal. If the travel speed in the operation is 5 mm/sec, determine (a) cross-sectional area of the weld bead, and (b) the feed rate (mm/sec) at which the filler wire must be supplied.
A cylindrical air-compressor tank with an inside diameter of 50 mm is to be designed to withstand safely a working pressure of 0.86 MPa. Boiler plate with an allowable tensile stress of 76 MPa. All seams will be butt welds with an expected efficiency of 100 percent. a.) Determine the force per lineal mm of longitudinal seam, b.) Determine the required thickness “t” of wall, c.) Determine the unit stress in the circumferential seam.
Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.
An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?
Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown below. For dynamic forces, both dynamics are synchronized, and when the force in the y-axis direction is downward, it is on the right in the x-axis direction. When the force is up, the other force is on the left. The welded part is made of 1018 HR steel, 10 mm thick. a) Safety factor for welding? b) Calculate the safety factor for the base metal. (Electrode type for question is E9010.)
A bracket, as shown in figure below, is welded to a plate. The welds have the same size, and thepermissible force per mm of the weld-length is 1 kN. Calculate the lengths l1 and l2.
A bracket to be welded into a steel channel using E-60 electrode 345 Mpa) Two welding sets are suggested as shown in Fig. (1)Based on maximum shear stress failure theory and safety factor of (2.5) (a) Find the weld size for each set. (b) Which set would you recommend A or B ?
It has been reported that gas–tungsten arc welds of aluminum made in the overhead position (assumed lap weld joint) tend to have a significantly higher porosity level than those made in the flat position: a. Explain why b. Sketch the general view of the overhead position c. Indicate where the (most probable) location of the porosity
The unit melting energy for a certain sheet metal is 10J/mm^3 .The thickness of each of the two sheets to be spot-welded is = mm. To achive required strength, it is desired to form a weldnugget that is =7 mm in diameter and 3.5 mm thick. The weld duration will be set at 44 sec .If the electrical resistance between the two surfaces is 144 micro-ohms and only one half the electricity generated will be used to form the weld nugget Determine the minium current level required in this operation