Answered: A bracket is as shown in figure 2.…

A bracket is as shown in figure 2. Determine the uniform weld size for the arrangement. The permissible shear stress of weld material is 80 MPa. Consider the loading condition as shown in figure.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Related questions

Q: A rectangular plate (0 =22") is formed by welding two triangular plates shown in figure. The plate…

Q: Q-2 The permissible shear stress for the weldment illustrated is 138 MPа. Estimate the load, F, that…

A: Given: The permisible shear stress is τper=138 MPa. The diameter of the weldment throat is d=75 mm.…

Q: A steel bar of thickness h is welded to a vertical support as shown in the figure. OV The dimensions…

A: To Find : The safe force F in KN. Given : Dimension of perimeter are b=70 mm, c=170 mm, d=70 mm,…

Q: The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the…

Q: A plate 60 mm wide and 12.5 mm thick is to be welded to another plate by means of parallel fillet…

Q: Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by…

Q: Q1/ A bracket is welded to a frame by two 10 mm fillet welds as shown in Fig., carries a load of 9…

A: Given: The size of fillet weld, t = 10 mm The length of weld, L = 56 mm The load acting, P = 9 kN…

Q: Do larger members fail at comparatively lower stresses than smaller members?

A: When a moment or couple is acting over the member, then the size of the member is a matter of…

Q: Find the resultant shear stress at point A & C for the weldment shown in the figure. Leg size of the…

Q: Find the position and the value of the maximum stress for the weld joint shown in the figure. Assume…

A: Introduction: The load-bearing capability of a weld relates to how much load it can withstand before…

Q: A plate I m long 60 mm thick is welded to another plate at right angles to each other by 12 mm fil-…

Q: For the closed tank as shown below, is subjected to a internal pressure of 1.5 Mpa, and tensile…

Q: Q-1 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by four fillet…

Q: e thickness of plate. I is 12 mm and plate. 2 is 10 mm. The yield stress an odulus of Elasticity for…

Q: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a thickness…

Q: P1.38 Two aluminum plates, each having a width b = 7.0 in. and a thickness t = 0.625 in., are welded…

Q: A bracket, as shown in figure below, is welded to a plate. The welds have the same size, and the…

A: Given data as per question Force per mm applied =1 kN Total load =120 kN Calculations According to…

Q: The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a…

A: As per the guidelines we have to solve only first question. So kindly you post the second question…

Q: A 50 mm long and 4 mm thick fillet weld carries a steady load of 10 kN along the weld. The shear…

Q: The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a…

A: Given data: b=49 mmd=48 mmh=5 mmτallow=148 MPa Need to determine the allowable force.

Q: column 350 3 kN 2 kN beam 80 140

Q: A rectangular plate (0 =21°) is formed by welding two triangular plates shown in figure. The plate…

A: Given data θ=21° Compressive stress=2.9 Mpa. Tensile stress=19 Mpa.To determine The normal…

Q: Q2/ According to the figure below find the size of the weld. Take permissible shear stress for the…

Q: The web plate of a built-up welded I-section is 200 mm x 12 mm and the flange plates are 100 mm x 12…

A: Given Web Allowable shear stress = 110 N/mm2 To find Maximum shear force

Q: A steel bar of thickness h is welded to a vertical support as shown in the figure. Find the safe…

A: Given:b=60 mmc=160 mmd=60 mmh=5 mmζallow=140 MPaWe have to find safe force F if the maximum…

Q: 13 Two steel rods are welded together (see figure); the seam is oriented at angle 0 = 50°. The…

A: Given data: The seam oriented at an angle is θ=50° The stresses on the rotated element are σx1=10…

Q: A plate 100 mm wide and 10 mm thick is to be welded with another plate by means of transverse welds…

A: Given Data⇒ Thickness of weld (t)=10 mm t=0.010 m Load (F)=70 KN Permissible tensile stress is…

Q: welded joint, as shown in figure below, is subjected to an eccentric load of 250 ze of the weld, if…

A: Given Data⇒ Eccentric loading(P)=2500 N Maximum shear stressζmax=50Nmm2

Q: I- The two plate-shaped parts given below are joined with a rivet. Examine this figure and formulate…

A: Part (1): For this case, total shear force is transmitted through highlighted single red face (as…

Q: 2 m 10 m

A: As this question is multipart, I will be solving only one question. Diameter of the cylinder is 2…

Q: A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the…

Q: A steel plate, 80 mm wide and 10 mm thick, is joined to another steel plate by means of a single…

A: Given data as per question width of plate =80 mm Thickness of plate (h) =10 mm Permissible tensile…

Q: The permissible stress in a fillet weld in 100MPA, and the fillet weld has equal base and height of…

Q: Q1: The weldment shown in the figure is subjected to a force F. The hot-rolled steel bar has a…

A: Use throat thickness concept to solve this prob, Find allowable F?

Q: P= 28 kip -Rigid plate T= 550 kip-ft Plane of weld Figure P6-89

Q: A beam 1m long with dimensions b = 50 mm and d = 100 mm is subjected to a load of 500 kgs as shown.…

Q: Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of…

A: a) The wide of the plate is given as,(w)=100 mm. The thickness of the plate is given as,(t)=10 mm.…

Q: A plate 100 mm wide and 12.5 mm thick is to be welded to another plate by means of parallel fillet…

Q: View Policies Current Attempt in Progress The assembly shown in the figure consists of rod (1) and…

Q: A pressurized cylindrical container, as in the figure, is made of 12 mm thick plate as shown in the…

Q: 5) Based upon data given in Fig. 2, the primary shear stress generated in the eccentric loaded weld:…

Q: Figure 4 shows a rectangular hollow steel bar welded to a vertical member. The bar has to support a…

Q: Q2/ Two welds, having length Li=150 and L2=200 are required to attach a plate to a column, as shown…

Q: A plate 100 mm wide and 10 mm thick is to be welded with another plate by means of transverse welds…

A: Given Data Width of the plate, w=100mm The thickness of the plate, t=10 mm Load, P=70KN permissible…

Q: 2. The figure shows welded hand rotates a shaft via a key. The key material allowable shear strength…

A: Given data: 1. Force acting on the weld 2. Dimensions of the weld and other dimensions. Both the…

Q: Question 1 A 50 kN load is transferred from a welded fitting into a 200 mm Figure 1. steel channel…

Q: A rectangular steel plate is welded as a cantilever to a vertical column and supports a single…

A: Given P=60kn =60000N b=100mm l=50mm ζ=140Mpa=140N/mm2Let S=weld sizet=throat thickness =0.707S…

Q: A plate 70mm wide and 15mm thick is joined with another plate by a single transverse weld and a…

A: According to the given information plate 70 mm wide and 15 mm thick, maximum tensile stress 60…

Q: A 40mm thick steel bar that is fabricated by welding two parts together is shown below. Being…

A: Given :-

Question

A bracket is as shown in figure 2. Determine the uniform weld size for the arrangement. The permissible shear stress of weld material is 80 MPa. Consider the loading condition as shown in figure.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.