Q#3: Design an 11- bus power system in ETAP and perform 3-phase short circuit analysis on bus#7 using overcurrent Relay to detect the fault current and break the particular Circuit Breaker Connected at bus#7. Analyze the results. Answer

Q#3: Design an 11- bus power system in ETAP and perform 3-phase short circuit analysis on bus#7 using overcurrent Relay to detect the fault current and break the particular Circuit Breaker Connected at bus#7. Analyze the results. Answer

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.5P

See similar textbooks

Related questions

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: In the case of a three-phase symmetrical short circuit fault at the F1 point in the power system…

Q: Q3: - A three-phase fault occurs at bus-1 of the network shown in figure below. The pre-fault…

A: Given data : Pre-fault voltage Eg''=Em''=Vf=1.05∠0° per unit

Q: B-For the radial shown in the figure below, calculate: 1- the fault currents for the faults.: FA and…

Q: Draw the negative- and zero-sequence impedance networks for the power system shown below. Mark the…

A: In this question we need to draw negative sequence and zero sequence per unit impedance diagram of…

Q: circuit diagram for electrical fault detector system for a three-phase transmission line

A: It is asked to show the circuit diagram of electrical fault detector system for a three-phase…

Q: For the following network, calculate the fault currents (IF1, IF2, IF3 and IF4) in pu and in kA, and…

A: …

Q: Figure 8.26 shows a single-line diagram of a three-phase, interconnected generator- reactor system,…

Q: Above is the one-line diagram of a simple power system. Each generator is represented by an emf…

A: The Given symmetric fault occurs 1 through a fault impedance Zi=j0.08 perunit. To determine the…

Q: Q2/K/ The positive-sequence reactances for the power system shown in Figure are in per unit on a…

Q: Consider a system operating at rated values with sequence impedances given by Z, = j0.2577, Z,=…

A: A single line-to-ground failure happens when one conductor meets the neutral conductor or falls to…

Q: Draw the fault current direction both in CTs and operating relay coils for internal and external LLL…

A: Here, question has asked for multiple protection systems and each system has multiple types of…

Q: Draw the positive, negative and zero sequence networks and obtain the Thevenin equivalent circuits…

A: (a) Draw the per-unit zero-, positive-, and negative sequence networks on a 150-MVA, 13.8-kV base…

Q: 3) Draw the schematics of a HVDC and of a HVDC light, compare the systems evidencing advantages and…

A: HVDC means high voltage direct current is a method of electrical power transmission which uses…

Q: Explain how the value of fault current can be computed for L-L-G fault occurring at the terminals of…

A: Fault current: It is a current that comes into the picture when the fault occurs. The current is the…

Q: It is required to keep L-G fault current with zero fault impedance to rated line current. Determine…

A: According to question: The value of Z1 is given twice and Z0 is missing, so it is assumed that the…

Q: In the case of a three-phase symmetrical short circuit fault at the F1 point in the power system…

Q: (Q.3) Derive the expression of fault current for single line to ground fault occurring at phase 'a'…

A: L-G Fault: L-G fault refers to Line-ground fault. It is an unbalanced Fault. Whenever there is a…

Q: The fault current level of a circuit breaker used in a transmission line with phase voltage 5.2 kV…

Q: It is required to keep L-G fault current with zero fault impedance to rated line current. Determine…

A: In this question we need to find a reactance need to be placed in neutral of genrator to limit the…

Q: Thévenin equivalent sequence networks looking into the faulted bus of a power system are given with…

A: Given that z1=0.15 z2=0.15 z0=0.2 Vf=1∠0° (a) For three phase balanced fault Formula for fault…

Q: 5.20 Three individual 3-phase 400 kV power system, each one of which consists of a generator…

A: we need to explain about fault level if extra lines connected.

Q: Q2/The positive-sequence reactances for the power system shown in Figure are in per unit on a common…

A: Current: It is the time rate of the change of the charges. It is also known as the flow of the…

Q: V, =1.025Z0°pu P=300MW j0.05 Bus 1 Bus 3 V = 1.03 Slack j0.025 j0.025 Bus 2 400MW 200MVAR

A: The given power system can be redrawn as shown below:

Q: A 3-phase, 3-wire system has a normal voltage of 10-4 kV between the lines. It is supplied by a…

A: We have 3-Phase, 3-Wire system with, Normal Voltage (Vl) = 10.4 KV = 10.4 * 103 V Generator Positive…

Q: 2) Draw equivalent diagram for this network with all per unit resistances and reactance near their…

A: The detection and diagnosis of faults in technical systems, particularly using a strategy in which…

Q: Question 2: A single-line diagram of the power system is shown in Figure 2, where negative- and…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

Q: In the case of a three-phase symmetrical short circuit fault at the F1 point in the power system…

Q: Given the network shown, for a solid three phase fault on bus 2 (a) find the subtransient current in…

A: The state where the three conductors are physically held together with zero impedance between them,…

Q: In a 3 phase, 3 wire system, it has normal voltage of 10.4kV line to line fault occurs at generator…

A: For the 3- phase line to line the positive sequence phase current is evaluated as:

Q: For the following single line diagram of a three-phase system, a three-phase fault occurs at point P…

A: G1=20 MVA1=6.9 kVis taken as base valueXg1=0.15 pu Xg2(at new base)=0.08×2025×6.96.92…

Q: A 3-phase, 33 kV, 37.5 MVA alternator is connected to a 33 kV overhead transmission line. The…

Q: A three-phase short circuit occurs at point P for the system shown in the following figure. (a)…

A: In this solution, we'll discuss about pu impedance diagram & fault analysis of a power system.

Q: A 400KV single busbar substation with 4 outgoing feeders is protected by a high impedance…

A: Substation and its equipment's The single line diagram is the basic set of diagrams that is where…

Q: At a 220 kV substation of a power system, it is given that the three-phase fault level is 4000 MVA…

A: Given substation level=220 v Three phase fault =4000 MVA single line to ground fault=5000 MVA

Q: For the following single line diagram of a three-phase system, a three-phase fault occurs at point P…

A: Given data : G1 = 20mvA = 6.9kv which is taken as base value Xg1 = 0.15 pXg2 at new Base =…

Q: The fault current level of a circuit breaker used in a transmission line with phase voltage 2.2 kV…

Q: Thevenin equivalents of the zero, positive, and negative sequence circuits, respectively, seen from…

A: Each question has multiple subparts to solve. We are authorized to answer three subparts at a time,…

Q: Suppose V-1.0°p.u., z= j0.50 p.u., z z-jo.25 p.u.; draw a sequence network cannection in case of…

A: When there is no fault impedance present in between fault points then it is called bolted fault…

Q: Line to ground fault has the highest probability in the power system True False

A: TRUE

Q: a power system what happens to phase voltages for a single line-to-ground fault as fault reactance…

A: Assume that fault occurs at phase 'a' if three phase system Although fault phase voltage…

Q: Given the network shown, for a solid three-phase fault on bus 2 (a) find the sub transient current…

Q: The positive sequence reactance for the power system shown in Figure below are in per unit on a…

A: Given: The positive sequence reactance for the power system shown in the Figure below is per unit on…

Q: A 20 MVA, 11 kV, 3-phase, 50 Hz generator is connected in parallel with anothe identical generator.…

A: FAULTS IN POWER SYSTEM FAULT: In an…

Q: For the following single line diagram of a three-phase system, a three-phase fault occurs at point P…

A: Given vales, KVA=20,000 KVA KV=6.9KV Zp.u. of G1=j0.15 p.u.and Zp.u. of G2= 0.08 * SnewSold *…

Q: A 100-MVA, 18-kV generator is connected to a transformer. The generator has reactances of 19%, 26%…

A: Given: S=100 MVA VLmax.=18 kVReactances-Xd''=19% , Xd'=26% , Xd=130%Time constants-Td''=0.035 sec ,…

Q: The zero-, positive-, and negative-sequence bus impedance matrices for a three-bus three-phase power…

A: We are authorized to answer three subparts at a time. Since you have not mentioned which part you…

Q: A 10 MVA, 6-6 kV, 3-phase star-connected alternator having a reactance of 20% is connected through a…

A: The last digits of student ID is 21. Given information We need to draw the transmission line and…

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

None

Q#3: Design an 11- bus
power system in ETAP and
perform 3-phase short
circuit analysis on bus#7
using overcurrent Relay to
detect the fault current and
break the particular Circuit
Breaker Connected at
bus#7. Analyze the results.
Answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a 220 kV substation of a power system, it is given that the three-phase fault level is 4000 MVA and single-line to ground fault level is 5000 MVA. Neglecting the resistance and the shunt susceptances of the system, (B) And the zero sequence driving point reactance at the bus is: (@)2.2Q (b) 4.84Q (€)18.18 Q (d)22.72Q
Consider the single-line diagram of a power system shown below. The transient reactance of cach part of the system is as shown in table and expressed in p.u. on a common 100 MVA base. A three-phase fault with impedance of 0.16 p. occurs at bus (5). Determine short- circuit capacity (fault level) and short circuit current? Assume the fault voltage at bus (5) equal 112 KV
For the power system with a single line diagram; a) By choosing the base values of 1000 MVA and 20 kV in the Generator G3 region, the system is zero, Draw the reactance diagrams of the positive and negative sequence circuits. (for each line ?0 = ?1 = ?2 = 50 ?ℎ?) b) Find the Thevenin equivalents according to the fault condition in busbar 1.
Figure 1 shows a three-bus power system network of an electric utility company with each generator is represented by an electromotive force (e.m.f.) behind the transient reactance. All impedances are expressed in per unit on a common MVA base. The pre-fault system is on noload condition with 1.0 per unit voltage, and pre-fault currents are zero. All answer must be given in FOUR (4) decimal points. (a) Construct the bus impedance matrix for the system using building algorithm method.
Find the fault current in both generators and in the motor for a three-phase mid-line fault. Find stresses at nodes 1 and 2 during failure. Use the bus impedance matrix method Note: votage is 10000V
In the case of a three-phase symmetrical short circuit fault at the F1 point in the power system whose single line diagram is given below; Calculate the tripping current.
A three-phase circuit breaker has a 15.5-kV rated maximum voltage, 9.0-kA rated short-circuit current, and a 2.50-rated voltage range factor. (a) Determine the symmetrical interrupting capability at 10-kV and 5-kV operating voltages. (b) Can this breaker be safely installed at a three-phase bus where the symmetrical fault current is 10 kA, the operating voltage is 13.8 k V, and the (X/R) ratio is 12?
16. Which of the following is a solution to the problem of circulating currents?A. Integrating the grounding circuit supplying the equipment with the equipment itselfB. Incorporating surge arresters and surge protection devicesC. Using multiple-point grounding and two power supply systemsD. Connecting the equipment frames to several reference grid structures
Given the 4 bus network shown below, assume that there are no loads and all buses are at the rated voltage and all have the same phase angles. Assume that shunt capacitances are neglected. The relevant transient reactances for the generators and the reactances for the transformers are shown. Solve for the fault current through the fault impedance for a fault at bus 4 with a fault impedance of j0.1 pu. HINT: Use Delta to Wye conversion.
For the following network, calculate the fault currents (IF1, IF2, IF3 and IF4) in pu and in kA, and circuit breaker ratings (i.e. fault MVA ) at the indicated locations. Internal reactance of generators are j0.9 pu. Base quantities: 11 kV, 400 MVA on the generator side.
The fault current level of a circuit breaker used in a transmission line with phase voltage 5.2 kV and breaking capacity 70 MVA
1) For the utility radial distribution system shown on figure below (only generator is at 138kV). All impedances are in per unit on a 100MVA base and nominal voltage shown. All transformer connected taps equal nominal voltage shown. All breakers and switches are closed unless marked with N.O. (Normally Open). Calculate fault current magnitudes in rms symmetrical amps at the following locations (faults are bolted, one at a time, not simultaneous.)a. Three phase (3ph), phase to phase, and single line to ground (SLG) at 138kV bus.b. 3ph, and SLG at 34.5kV bus. 138/34.5 transformers have the same Z and are in parallel.c. 3ph, and SLG at 34.5kV at 34.5/12.47 substation high side.d. 3ph, and SLG at 12.47kV buse. 3ph, and SLG at 12.47kV tapf. 3ph, and SLG at 12.47kV end of line (EOL)g. State the 138kV source (generator) amps for the 3ph at 12.47kV EOL fault.