Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A and arm B is rotating at 200 rpm ccw. The gears E and F are carried by the arm. The gear G is rigidly attached to shaft C. Find the magnitude and direction of the speed of shaft C. If the gear train is transmitted 7.5 kW what is the torque required to hold shaft A stationary? Given that Z;=40, Zc=30 and Ze=20. E B A. D G

Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A and arm B is rotating at 200 rpm ccw. The gears E and F are carried by the arm. The gear G is rigidly attached to shaft C. Find the magnitude and direction of the speed of shaft C. If the gear train is transmitted 7.5 kW what is the torque required to hold shaft A stationary? Given that Z;=40, Zc=30 and Ze=20. E B A. D G

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

. During the operation of a punch press, its flywheel decelerates uniformlyfrom 400 rpm to 200 rpm in l sec. The rim of the flywheel weighs 1288 lb, itsinside and outside diameters are 56 in. and 60 in., and it is attached to itshub by 6 spokes. What average shearing force is developed between the rim andeach spoke during the 1 sec interval?
Shaft "a" in the figure rotates at 450 rev/min in the direction shown. Find the speed and direction of rotation of shaft "d".
A chain with speed of 900 fpm has driving sprocket turns at 1000 rpm. If the pitch of chain is 3/4-in, find the number of teeth of driving sprocket. (Ans. 14 teeth)
Q3/ A vertical double acting steam engine develops 80 kW at 240 rpm. The maximum fluctuation of energy is 25% of the work done per stroke. The maximum and minimum speeds are not to vary more than +1% of the mean speed. Find the mass of the flywheel, if the radius of gyration is 0.65 m.
Please draw the figure. Thank you so much.An engine flywheel and a clutch plate are both connected to a transmission shaft. Let the moment of inertia of the flywheel be I1 and its angular velocity ω1, and let the moment of inertia of the clutch plate be I2 and its angular velocity is ω2. The two discs have then been combined by forces which are applied at their axes of rotation so as not to cause any torque. The discs then reached a common final angular velocity after rotational collision. Find the expression for the final angular velocity.
The max speed for the servo shown is 130RPM when connected to 6V. Assume that the gearbox on your servo is able to output a torque of 1.5 kg-cm while turning at this speed. Using the number of teeth on each gearprovided in the table, determine the torque and rotational speed of the output shaft on the DC motor. HINT: Work backwards from the output shaft and use the equations developed in class that relate the number of teeth to the torque. When working back from the output shaft to gear 7/6, realize that the “torque” transmitted by gear 7 is the SAME as the torque transmitted by gear 6 since they are joined. Then, relate the torque of gear 6 to gear 5 based on their numbers of teeth. Since gears 5 and 4 are actually one piece, the torque in 4 and 5 will be the same (as was the case for gears 6 and 7). Repeat for the other gears, working your way all the way back to the DC motor.
A single cylinder reciprocating engine has speeded 300 RPM. Stroke 250 mm, mass of reciprocating parts 50 kg. Mass of revolving parts at 150 mm radius 37 kg. If two fourth of the reciprocating parts and all the revolving parts are to be balanced, find (i) The balance mass required at 400 mm radius (ii) The residual unbalanced force when the crank has rotated 45° TDC.
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
Two cylinders rolling in the opposite direction has a speed ratio of 3. If the diameter of driver is 10 inches, find the center distance between cylinders. A. 15 in B. 10 in C. 25 in. D. 20 in. Please solve the Problem elaborately. Your solution will be use as reference for my studies. Thank you so much your work will be appreciated much!
An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number. An electric motor has a rotor with a mass moment of inertia of 22 ft-lb-s2. What torque is required to accelerate it from rest to 1,174 rpm in 3.6 seconds? Provide your answer in lb-ft and round to the nearest whole number.
A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
a) A single cylinder reciprocating engine has a stroke 40cm and the crank makes 250 r.p.m. The reciprocating parts mass is 60kg and the mass of the revolving parts at 20cm radius is 40kg. If two-thirds of the reciprocating mass and all the revolving mass is to be balanced, what is the balancing mass at a radius of 40cm and what is the residual unbalance force when the crank is at 60º from the top dead centre. b) A shaft is supported at bearing at A and B, 2m apart. A rotor of total mass 30kg is mounted at a point 0.6m from bearing A. Owing to faulty mounting the centre of gravity of the rotor is offset 3mm around the axis of rotation. Calculate the dynamic loads on the bearings when the shaft rotates at 600rev/min. calculate also the maximum and minimum loads on the bearings.