Q3) The unsteady flow of water through the reducer shown in Fig.2 is such that the velocity at A is VA = 10t m/s .Calculate the average velocity at B and the average acceleration at A,when t 2s. The diameters of the pipes shown in Fig.2 0.1 m 0.3 m B A Fig.2

Q3) The unsteady flow of water through the reducer shown in Fig.2 is such that the velocity at A is VA = 10t m/s .Calculate the average velocity at B and the average acceleration at A,when t 2s. The diameters of the pipes shown in Fig.2 0.1 m 0.3 m B A Fig.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Water at 10°C is flowing from point A to point B through the fabricated section shown below at the…

A: Given that: Volume flow rate = 0.37 m3/s Diameter at A = 300 mm = 0.3 m Diameter at B = 600 mm = 0.6…

Q: Q3) The unsteady low of water through the reducer shown in Fig.2 is such that the velocity at A is…

Q: Problem: Reservoir A has an elevation of 105 m. A pipe is connected from reservoir A to reservoir B.…

A: The overall pressure losses incurred by the fluid as it moves from the suction point to the…

Q: Petrol is drained from a tank X to tank Y via pipeline A-B (see figure Q3). A pump is then used to…

Q: Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular…

A: We have, Diameter, d=200 mm=0.2 m, V=3 m/s Diameter of circular plate, d1=150 mm=0.15 m (as…

Q: Compute the force that must be applied to prevent the cart in the figure from accelerating. The…

A: Here, we will use impulse-momentum equation to find the force. The force that needs to apply will be…

Q: A pipe with an inner diameter of 4 inches contains water that flows at an average velocity of…

A: Given data: The inner diameter of the pipe is d=4 in=0.1016 m The average velocity of the water is…

Q: The head of water at the inlet of a pipe of length 1 500 m and diameter 400 mm is 50 m. A nozzle of…

Q: anometer being used to indicate the pressure difference between two points in a fabricated system.…

Q: I need the answer as soon as possible

A: Dear student, According to the guidelines I am allowed to answer only one…

Q: 3: Water flows through a 100 mm diameter pipe at velocity of 4.5m/sec. Find the discharge.

A: Given:d=100 mmV=4.5 m/s

Q: Qil A (30 N/s) flow throw the reducer of the proceeding problem ,the air in the (300mm) pipe having…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Q1) Water flowing through a jet with velocity of 30 m /s. Caleulate the value of (0) to be the water…

Q: Question 2: A Pelton wheel turbine is used in a hydroelectric plant to generate electric power. In…

A: The velocity diagram for the symmetrical blade of a Pelton wheel is given below,

Q: Find the discharge in litres/s of the pipe of diameter 35 mm with the velocity of water 3.5 m/s. The…

Q: Q4/ Gas (p = 0.0022 lb/ft) flows through duct shown in fig. At A flow rate is 60 ft /s under a…

Q: 4.) A 7 mm diameter tube is connected in series to a 38 mm diameter tube. Water flows at 8.5 m/s in…

Q: 14. Create an illustration of a large water cooler that contains water up to a height that contains…

Q: Q4- When the flow is completely turbulent, increasing value of Re no. have no effect on the value of…

A: the effect of Reynold no on the friction factor.

Q: Residents of a certain town are happy because a fountain is to be designed for the park. A nozzle…

Q: A fluid flows at 650 (ft^3)/min through the space between two concentric pipes. The inner pipe has…

A: Given: Q = 650 ft3 /min d = 1.5 in. D = 4 in. To find: Average velocity, uavg = ?

Q: A water stream at pipe AB divides into two branches as shown in the figure below. The average…

Q: In an experiment, it was found that the jet issuing horizontally under a head of 1m travelled a…

A: Given: The value of the head is, H=1 m. The value of horizontal is, X=1.5 m. The value of the…

Q: Find discharge A=3 m2 V=2.2 m/s

A: Given that , A=3m2V=2.2m/s

Q: Water @ 4C flows through a 100-mm ID smooth pipe. The Reynolds # of the flow is 150000. Determine…

A: To Find : The maximum velocity. Given : The diameter is d=100 mm. The Reynolds number flow is…

Q: Q1: A nozzle is situated at a distance of 1.2 m above the ground level and is inclined at 60° to the…

A: given data . diameter of jet = 40 mm angle = 60° Sy= 1.2 m Sx= 5 m find the flow rate .

Q: Q3) The unsteady flow of water through the reducer shown in Fig.2 is such that the velocity at A is…

Q: 6. Water enters a hydraulic reaction turbine with a velocity of 12 ft per sec and leaves it 3 ft…

Q: 22/Water flows steadily through the nozzle shown in Figure No. (2) at flow rate Q= 0.06 (m³/s). The…

A: Since you have uploaded multiple question, as per the guidelines we will answer the first question…

Q: Water is flowing in a 2-inch pipe at an average velocity of 10 m/s. Assuming the flow is laminar,…

A: d=2in

Q: Q1: If flow rate in pipe shown is (0.5m'/s) find the (H). H. water D=300 mm

A: Given data Volume flow rate = Q = 0.5 m3/sDiameter of pipe = 300 mm = 0.3 m

Q: An industrial tank is discharging a fluid through a 5-inches nozzle with a velocity of 5 meters per…

A: Given : d = 5 in = 0.416 ft v = 5 m/s = 16.404 ft/s Q = 300 Gal/min D = 10 ft H = 20 ft To find :…

Q: A fabricated assembly made from three different sizes of standard steel tubing is shown below. The…

Q: Calculate the shear stress in lb/ft2 at the centerline of the 4.7-inch diameter pipe carrying water…

Q: What is the pipe area, A? Find flow velocity, V.

Q: Water flows at a constant speed of 20 m/s through narrow section of the pipe. What is the speed of…

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

Q: A pipe transports 1962 N/s of water. The pipe tees into a 2"-diameter pipe and a 3"-diameter pipe.…

Q: Q1: If flow rate in pipe shown is (0.5m/s) find the (H). H. water D=300 mm

Q: Water flowing through a contraction pipe with diameter of 20mm and 5 mm respectively. If the…

Q: mm is 3 m/s, the velocity in the sub-channel of width 300 mm is m/s.

A: Given data; Width=450 mmflow rate=0.9 m3/sD=300 mmd=200mmvelocity in te channel of 200 mm…

Q: Q1) A glass tube is inserted into a flowing stream of water with one opening directed upstream and…

A: “Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: A jet of water from a nozzle discharging into air has a diameter of 6 in and a mean velocity of 120…

Q: (Q6) Assuming ideal flow in a horizontal plane, calculate the magnitude and direction of the…

Q: 3.7 m 4 cm diameter Group (D) 7.2 m Determine the discharge, the velocity of flow and pressure at…

Q: The vein's diameter shrinks to 0.5 times its initial size as a result of contraction. If the…

A: Given Data: The velocity of the blood flowing in the vein, V1=10 m/s

Q: A pump draws water from reservoir A and lifts it to reservoir B as shown. The head loss from A to 1…

Q: A 3' diameter ppe flows full when it carries 30 cfs. find the discharge and depth in the pipe if the…

A: Given data: The diameter of pipe D0 =3ft Full flow rate Q=30 cfs The velocity of flow at any depth…

Question

Q3) The unsteady flow of water through the reducer shown in Fig.2 is such that the
velocity at A is VA = 10t m/s .Calculate the average velocity at B and the average
acceleration at A,when t = 2s. The diameters of the pipes shown in Fig.2
0.1 m
0.3 m
B.
A
Fig.2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the siphon in Fig. 6.26, calculate the distance X re-quired to obtain a volume flow rate of 7.1 X 10-3m³/s.
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
Use the Manning equation to find the Flow Rate.
Water flows at a rate of 500 gal/min through a 400-ft-long line. The first and last 100 ft of the line are 6-in-diameter cast iron pipes, while the middle 200 ft consists of two 4.24-in-diameter cast iron pipes. Find: a. Provide a diagram b. the average velocity in each section of pipe, c. the pressure drop in each length of pipe, and d. the total pressure drop.
The velocities of flow in a 1 m diameter pipe are 6 m/s on the centerline and 4.85 m/s at x=100 mm. Determine discharge
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
A 3' diameter ppe flows full when it carries 30 cfs. find the discharge and depth in the pipe if the velocity is 3fps
Benzene flows through a 100 mm diameter pipe at a mean velocity of 3 m/s. Find discharge in liter per second.
Two pipes with C1= 120, connected in series, discharge 4.75 cfs with a loss of head of 27 ft. Each pipe has a length of 1000 ft.If one pipe has a diameter of 18 inches, determine the diameter of the other pipe. Neglect minor losses.
The water in an aquarium will be drained for cleaning. A flexible tube (D = 4mm) will be used to drain the aquarium through siphoning. If the vertical distance between the end of the tube and the water surface is 6Ocm, solve the volumetric flowrate.
Question 8 Two reservoirs are connected by a pipe whose total length is 360m.From the upper reservoir the pipe is 300mm in diameterfor a length of 150m and the remaining 210m is 450mm in diameter.The difference in water levels between the two reservoirs are 8m.Take f=0.006 for the smaller pipe and f=0.005 for the larger pipe.If all the changes in pipe sections are sharp and sudden, calculate the flow rate which can be delivered.