(Q6) Assuming ideal flow in a horizontal plane, calculate the magnitude and direction of the resultant force on the blade. Note that the jet (UC = 15m/s, dc= 150mm and UCB=3m/s which moves the blade away from the jet ).The jet UC is divided by the splitter so that one third of the water is discharged from A. %3D

(Q6) Assuming ideal flow in a horizontal plane, calculate the magnitude and direction of the resultant force on the blade. Note that the jet (UC = 15m/s, dc= 150mm and UCB=3m/s which moves the blade away from the jet ).The jet UC is divided by the splitter so that one third of the water is discharged from A. %3D

Name: (Q6) Assuming ideal flow in a horizontal plane, calculate the magnitu
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: (Q6) Assuming ideal flow in a horizontal plane, calculate the magnitude anddirection of the resultant force on the blade. Note that the jet(UC = 15m/s, dc= 150mm and UCB=3m/s which moves the blade away from thejet ).The jet UC is divided by the spli

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
-, Given: Water from a pressurized tank flows out and creates a vertical jet as shown. Total head loss due to friction is 5 m At location A. a pump adds 20 J/kg in the direction of flow to the stream Water properties are as follows: p= 998 kg/m and u= 1E-3 Ns/m. Acceleration due to gravity is g= 9.81 m's?. Find: Maximum height H to which the jet rises. Air 75 kPa (gage) H? Water 85 cm
Q2) Find the value and direction of the force applied on an curved blade as shown in the figure below If the angle(0 = 120°), jet velocity is (30 m/sec), and the 20 discharge 10 L/sec. U2 @=128 U₁ X₂ F
Water flows steadily through a pipe with ID 35 mm. This pipe expands suddenly to an inner diameter of 75 mm and then stays at that diameter. The flow speed in the 35 mm pipe is 32 m/s. The water gage pressure in the thinner pipe is 510 kPa. 1. What is the pressure at the entrance to the thicker section of the pipe? Is the pressure there larger or smaller than in the thin pipe section? 2. What force is acting on the coupling? Is it tension or compression?
A two-dimensional reducing bend has a linear velocity profile at section 1. The flow is uniform at sections 2 and 3. The fluid is incompressible, and the flow is steady. Find the maximum velocity at section 1, V1,max.
Question 1: Water is expelled by a jet to the environment (i.e. the water flow is surrounded by atmospheric pressure). To change the direction of the water flow, this enters to a curved pipe as show in the figure (top view perspective). Calculate the forces exerted by the flow to the pipe in x and y direction (both horizontal). Use a water density of 1000 kg/m³, Q=1 m³/s, diameter d-0.3 m. Follow the 4 steps explained in the lectures and state your assumptions clearly. 30 Question 2: Repeat question 1 but change the curvature from 30 degrees to 90 degrees. How the forces change? 90
out Water flows steadily in a two- duct dimensional bend. The incoming velocity to the bend is parabolic with maximum velocity equal to 9 ft/s. The inclination of the bend is a = 2h V. The width of the duct is constant тах (2h = 30 inches). After the bend, the velocity is uniform and equal to Vout- Compute and sketch the force required to keep the bend in place.
A pipeline of constant 0.6 diameter with its centerline in the horizontal plane turns through an m U2 of 75° (Figure angle pipeline carries water at the rate of 0.85 m3/s. A pressure gauge at 3). The she bend indicates that the pressure is equivalent to 41.3 m of water. Calculate the force exerted U1 on the bend by the water and the direction it acts. Fiaure 3 1080 ace
The waterwheel in Fig. is being driven at 200 r/minby a 150-ft/s jet of water at 20 ° C. The jet diameter is 2.5 in.Assuming no losses, what is the horsepower developed bythe wheel? For what speed Ω r/min will the horsepowerdeveloped be a maximum? Assume that there are manybuckets on the waterwheel.
A reducing bend has a linear velocity at section 1. See Figure 4. The flow is uniform at sections 2 and3. The fluid is incompressible and the flow is steady. The fluid is has specific weight γ = 64.4lb/ft3 and densityρ = 2slug/ft3. Assume unit depth into the page.(a) Find the magnitude and direction of the uniform velocity at section 3.(b) What’s the momentum of the fluid entering the reducer bend?
A sink of strength 20 m2/s is situated 3 m upstream of a source of 40 m²/s in a uniform stream. It is found that, at a point 2.5 m from both source and sink, the local velocity is normal to the line joining the source and sink. Find the velocity at this point and the velocity of the uniform stream. Locate any stagnation points and sketch the flow field.
5. A linear velocity profile is formed in a fluid between two plates as shown in the figure when one of the plates is moved parallel to the other and there is no externally imposed pressure gradient (i.e. there is no pump). If the top plate is travels at U = 0.3 m/s and the bottom plate is held fixed and the two plates are separated by a distance d = 0.3 m/s, derive an equation for the velocity profile u(y). Assume that the fluid in contact with either plate moves at the same speed as the plate (this is called the no-slip condition). U=0.3 m/s d=0.3 m