Q3: The Y-connected source in figure feeds a delta-connection load through a dis an impedance of I+jl Q/o. The load impedance is 118 + 185 /o Use the a-phase internal voltage of the generator as the reference a) Construct a single phase equivalent cireuit of the 3-6 system. b) Calculate the line currents laa Ipa and Ie. c) Calculate the phase voltages at the load terminals. Erhe Joad

Q3: The Y-connected source in figure feeds a delta-connection load through a dis an impedance of I+jl Q/o. The load impedance is 118 + 185 /o Use the a-phase internal voltage of the generator as the reference a) Construct a single phase equivalent cireuit of the 3-6 system. b) Calculate the line currents laa Ipa and Ie. c) Calculate the phase voltages at the load terminals. Erhe Joad

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZrY = 50 + j50 N , ZYB = 150 + j0 N and ZBr = 50 –j50 N. jos (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
Describe the concept of three-phase power in electrical systems and its advantages over single-phase power.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5 + j3 and 2 + j4.5 ohms are connected in parallel to a 7900-V source. Their secondaries are supplying a common load of 30 + j40 ohms. What is the magnitude of the voltage across the load in volts? (2 decimal places)
Two 7970-V:230-V single-phase transformers with impedance with respect to their secondaries of 1.5 + j3 and 2 + j4.5 ohms are connected in parallel to a 7900-V source. Their secondaries are supplying a common load of 30 + j40 ohms. A. What is the magnitude of the voltage across the load in volts? (2 decimal places) B. What is the magnitude of the total current supplied by the 7900-V source in amperes? (3 decimal places) C. What is the efficiency of the parallel transformers combined in percent? ( 1 decimal place)
Explain current divider rule in ac circuits with two parallel impedances Z1 and Z2. Calculate the currents I1 and I2 in phasor form for the circuit given in figure.
In the 3-phase circuit in the figure, f = 2000 Hz. Find line and phase voltages and currents for the load.(in amplitude and phase).
Problem 5 Consider a three winding transformer with the following particulars: = Z₁ Z2 Z3 =0.02 + j0.08 £, V₂ = 400 V, 12 = 60/30° A, and I3 = 50/-40° A. Assume that V₂ is the reference phasor, calculate: The intermediate voltage Vo. a. b. The primary current I₁ and the primary voltage V₁. c. The tertiary voltage V3 referred to the primary side. d. The apparent powers and the power factors at the primary, secondary and tertiary terminals. e. The transformer efficiency.
2) A 30- resistor, a 15-0 inductive reactance, and a 12- capacitive reactance are connected in parallel across a 120-V 60-Hz line. Find (a) the phasor branch currents, (b) total current and phase angle, (c) impedance, and (d) power drawn by the circuit.