Q3. An ac source in series with an impedance of (0.5 + j10) is connected to a transmission line having an equivalent impedance of (5 + j12) through an ideal step-up transformer with a-ratio of 0.05. An ideal step-down transformer with a- ratio of 25 connects the other end of the transmission line to a load of (30+ j40). If the voltage across the load is 240V, draw the equivalent circuit and determine: I- The power supplied to the load. II- The power dissipated by the transmission line. III- The power supplied by the source.

Q3. An ac source in series with an impedance of (0.5 + j10) is connected to a transmission line having an equivalent impedance of (5 + j12) through an ideal step-up transformer with a-ratio of 0.05. An ideal step-down transformer with a- ratio of 25 connects the other end of the transmission line to a load of (30+ j40). If the voltage across the load is 240V, draw the equivalent circuit and determine: I- The power supplied to the load. II- The power dissipated by the transmission line. III- The power supplied by the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

a) Explain the construction of LVDT. Identify some suitable examples according to their applications.b) Discuss contacting and non-contacting tachometers.
For the circuit shown in the given figure, assume that Vg˜=45 ∠0 V rms��~=45 ∠0 V rms , Rg = 9 Ω, and Ro = 5 Ω. Assume an ideal transformer. The power Psource supplied by the voltage source. The power Psource supplied by the voltage source is ________ W.
As given in the figure, an ideal transformer with a 2: 1 winding ratio is fed from a 240 Volt source with an internal impedance of 8 + j6 Ω and transfers maximum power to the load impedance connected at its secondary. So, which of the following is the V2 voltage in the secondary?
For the circuit shown in the given figure, assume that Vg˜=45 ∠0 V rms��~=45 ∠0 V rms , Rg = 9 Ω, and Ro = 5 Ω. Assume an ideal transformer. Find the equivalent resistance seen by the voltage source. The equivalent resistance is ________∠___________ Ω.
Basic & construction topic. EE
Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit equivalent circuit shown in part (c) contains an ideal transformer which cannot be accommodated by some computer programs. (a) True (b) False (ii) In the - circuit representation for real c in part (d), the admittance parameters Y11 and Y12 would be unequal. (a) True (b) False (iii) For complex c, can the admittance parameters be synthesized with a passive RLC circuit? (a) Yes (b) No
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
The impedance ZL in the circuit shown in Figure is adjusted for maximumaverage power transfer to itself.(a) What should be the value of ZL?(b) What is the maximum average power delivered to ZL?(c) What percentage of the average power delivered to the linear transformer is delivered to ZL?
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
Wiat is the difference between a real independent voltage source and an ideal independent voltage source? Give an example of a real voltage source and explain how it differs from the ideal.
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection