Q4: A diffuser, has air entering at 100 kPa, 280 K, with a velocity of 200 m/s. The inlet cross-sectional area of the diffuser is 100 mm2. At the exit, the area is 860 mm2, and the exit velocity is 20 m/s. Determine the exit pressure and temperature of the air. Take Cp=1.005 KJ/kg.K A: 280 K B: 300 K OC: 320 K OD: 340 K

Q4: A diffuser, has air entering at 100 kPa, 280 K, with a velocity of 200 m/s. The inlet cross-sectional area of the diffuser is 100 mm2. At the exit, the area is 860 mm2, and the exit velocity is 20 m/s. Determine the exit pressure and temperature of the air. Take Cp=1.005 KJ/kg.K A: 280 K B: 300 K OC: 320 K OD: 340 K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

It is proposed that a nozzle receive air at 2 m/s, 300 K, and 150 kPa, attemperature of 280 K, and a velocity of 100 m/s. The mass flow rate is 0.1 kg/s. The surface of the nozzle is kept at 270 K. Assuming that the air behaves as an ideal gas with constant specific heats. Is this process possible?Given: Vel1 = 2 m/s, T1 = 300 K, P1 = 150 kPa, Vel2 = 100 m/s, T2 = 280 K, P2 = 110 kPa, dm/dt = 0.1 kg/s, Cp,air = 1.005 kJ kg-1 K-1
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Steam expands adiabatically in a nozzle from inlet conditions of 130(psia), 420(°F),and a velocity of 230(ft)(s)−1 to a discharge pressure of 35(psia) where its velocity is2000(ft)(s)−1. What is the state of the steam at the nozzle exit, and what is SG for theprocess?
Four pounds of air gain 0.491 Btu/R of entropy during a nonflow isothermal process. If p1=120 psia and V2=42.5 ft3, find (a)V1 and T1, (b) W, (c) Q and (d) change of internal energy.
A type of liquid (density = 1500 kg/m3) passes through an adiabatic nozzle having an inletdiameter of 6 in. What should be the diameter (mm) at the exit in order to have a velocitythat is 3 times faster than the velocity at the inlet.
Consider the flow system illustrated below operating at steady state Obtain the maximum value of the velocity in the pipe 3, ?3??? (in cm/s).
Given that for a flow process the steady flow equation is
Q3// In a nozzle air at 700°C and twice atmospheric pressure enters with 50 m/s velocity, and leaves at a temperature of 40°C. Determine velocity of air at exit. Take Cp 1.005 kJ/kg.K for air.
In a natural gas pipe line compressor, 110 m^3/min of propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38 degree C. The process follows pV^1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature in kelvins, (b) the mass flow rate in kg/s, and (c) the heat loss in kW. And also draw the P-V and T-S diagrams.
20 - Helium enters a continuous flow compressor at 336 K and leaves at 451 K. If the mass flow rate is 1.4 kg/s, which of the following is the required power? (Cp = 5.1926 kJ/kgK) a) 927.9 kW B) 895.7 kW NS) 617.9 kW D) 836.0 kW TO) 988.7 kW
Helium expands polytropically steadily through a turbine according to the process pV1.5=C. The inlet temperature is 1000°K, inlet pressure 1000 kPa, and the exit pressure is 150 kPa. The turbine produces 100,000 kW. Determine (a) the exit temperature; (b) the mass flow rate kg/sec. RHe= 2.077 kJ/kg.K; k=1.666. Draw and label the P-V and T-S diagrams.
Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). A nozzle is a device that is used to increase the velocity of a fluidby varying the cross-sectional area. At the last section of a jetengine (Fig Q1.a, section 5), air with a mass flow rate of 50 kg/s ata pressure of 500 kPa and a temperature of 600 K enters a nozzlewith an inlet cross-sectional area of 5 m2. The exit area of thenozzle is 20% of its inlet area. The air leaves the nozzle at avelocity of 300 m/s. The nozzle is not well-insulated and duringthis process, 5 kJ/kg heat is lost. (iv) Determine the temperature of the air as it leaves the nozzle.(v) Calculate the pressure of the air as it leaves the nozzle.