I need the answer as soon as possible Q4) A large tank with an open top, containing water. The water can drain from the tankthrough a hose of diameter 9.6 cm. The hose ends with a nozzle of diameter 3.25 cm. arubberstopper is inserted into the nozzle. The water level in the tank is kept6.5 m above the nozzle.(a) What mass of water flows from the nozzle in 2.00 h if The stopper is removed. ?(b) Calculate the gauge pressure of the flowing water in the hose just behind the nozzle(3)(2)(1)figure(1)

Answered: Q4) A large tank with an open top,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You wish to water your garden with 100 ft of 5/8-in-diameterhose whose roughness is 0.011 in. What will be the delivery,in ft3/s, if the gage pressure at the faucet is 60 lbf/in2?If there is no nozzle (just an open hose exit), what is thethe maximum horizontal distance the exit jet will carry?
The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
A pump delivers gasoline at 20°C and 12 m3/h. At the inletp1 =100 kPa, z1 = 1 m, and V1 = 2 m/s. At the exit p2 = 500 kPa, z2 = 4 m, and V2 = 3 m/s. How much poweris required if the motor efficiency is 75 percent?
A pump delivers gasoline at 20 degrees Celsius and 12 (m^3)/h. At the inlet p1=100 kPa, z1=1 m, and V1=2 m/s. At the exit p2=500 kPa, z2=4 m, and V2=3 m/s. How much power is required if the motor efficiency is 75 percent?
Consider the incompressible flow of water through a divergent duct, where the inlet has a velocity & section area of 5 ft/s & 10 ft2. If the exit area is 5x the inlet area and the density of water is 62.4 lbm/ft3, solve for the pressure difference. (Please type answer no write by hend)
A two storey building has two faucets, one in the basement and one in the firstfloor. The maximum water (ρ = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm.Neglect all losses. What would be a maximum height (from the basement floor) for a faucet,to still get a maximum exit velocity of 6 m/s?
Here, a flow rate of 2 m3/s is active in a pipe, as seen in the attached figure. What is the expected power output of the turbine with 70% efficiency if the elevation difference of the reservoir surfaces is 60 m? How would I draw a EGL and HGL for this system?
A water truck drives slowly around a construction site, spraying water to keep dust down. A pump maintains a constant pressure of 100 kPa, gage, and the water is dispersed through 20 spray nozzles, each of diameter 0.01 m. If the truck is initially filled with 4000 L of water, and the flow rate is constant, determine how long the truck can drive before a refill is necessary in seconds.
A pump is 2.2 m above the water level in the sump and has a pressure of –20 cm of mercury at the suction side. The suction pipe is of 20 cm diameter and the delivery pipe is short 25 cm diameter pipe ending in a nozzle of 8 cm diameter. If the nozzle is directed vertically upwards at an elevation of 4.2 m above the water sump level, determine the elevation in meters, above the water sump level, to which the jet would reach. Neglect all losses. a.24.04 b.0.10 c.20.31 d.0.52
A gasoline pump fills a 80-L tank in 1 min 30 s. If the pump exit diameter is 4cm, what is the average pump-flow velocity?
The waterwheel in Fig. is being driven at 200 r/minby a 150-ft/s jet of water at 20 ° C. The jet diameter is 2.5 in.Assuming no losses, what is the horsepower developed bythe wheel? For what speed Ω r/min will the horsepowerdeveloped be a maximum? Assume that there are manybuckets on the waterwheel.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS