The system in Fig. consists of 1500 m of 4 cm iron-galvanized pipe, two 45°and two 90° screwed regular elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 350 m, what gage pressure is required at point 1 to deliver 0.006 m/s of water at 20°C into the reservoir. For water at 20°C, take p = 998 kg/m³ and µ = 0.001 kg/m.s. Elevation 500 m Sharp exit 45 Open globe 45 D

The system in Fig. consists of 1500 m of 4 cm iron-galvanized pipe, two 45°and two 90° screwed regular elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 350 m, what gage pressure is required at point 1 to deliver 0.006 m/s of water at 20°C into the reservoir. For water at 20°C, take p = 998 kg/m³ and µ = 0.001 kg/m.s. Elevation 500 m Sharp exit 45 Open globe 45 D

Name: zain IQAsiacellquiz 1 b.pdf >( 10 marks)Quiz 1/The system in Fig. con
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: zain IQAsiacellquiz 1 b.pdf >( 10 marks)Quiz 1/The system in Fig. consists of 1500 m of 4 cm iron-galvanized pipe, two45°and two 90° screwed regular elbows, a fully open flanged globevalve, and a sharp exit into a reservoir. If the elevation at poin

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
An 11.5-in-diameter centrifugal pump, running at1750 r/min, delivers 850 gal/min and a head of 105 ftat best efficiency (82 percent). (a) Can this pump operateefficiently when delivering water at 20°C through200 m of 10- cm-diameter smooth pipe? Neglect minorlosses. (b) If your answer to (a) is negative, can thespeed n be changed to operate efficiently? (c) If youranswer to (b) is also negative, can the impeller diameterbe changed to operate efficiently and still run at1750 rev/min?
Two 32-in pumps from Fig. are to be used in seriesat 1170 r/min to lift water through 500 ft of vertical castiron pipe. What should the pipe diameter be for most effi -cient operation? Neglect minor losses.
The pipe fl ow in Fig. is driven by pressurized air inthe tank. What gage pressure p1 is needed to provide a 208Cwater flow rate Q = 60 m3/h?
The head-versus-flow-rate characteristics of a centrifugalpump are shown in Fig.. If this pump drives water at20°C through 120 m of 30-cm-diameter cast iron pipe,what will be the resulting flow rate, in m3/s?
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
A test on 30-cm-diameter pipe with water showed a gage difference of 33 cm on mercury-water manometer connected to two piezometer rings 120 m apart. The flow was 0.23 m/s. What is the friction factor?
The tank–pipe system of Fig. is to deliver at least11 m3/h of water at 20°C to the reservoir. What is themaximum roughness height ε allowable for the pipe?
HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa