Q4: A piston-cylinder assembly whose piston is resting on a set of stops contains 0.5 kg of helium gas, initially at 100 kPa and 25°C. The mass of the piston and the effect of the atmospheric pressure acting on the piston are such that a gas pressure of 500 kPa is required to raise it. How much energy must be transferred by heat to the helium, in kJ, before the piston starts rising? For the helium, assume ideal gas behavior with C, = 5/2 R. Hln -05 kg A100 Pe

Q4: A piston-cylinder assembly whose piston is resting on a set of stops contains 0.5 kg of helium gas, initially at 100 kPa and 25°C. The mass of the piston and the effect of the atmospheric pressure acting on the piston are such that a gas pressure of 500 kPa is required to raise it. How much energy must be transferred by heat to the helium, in kJ, before the piston starts rising? For the helium, assume ideal gas behavior with C, = 5/2 R. Hln -05 kg A100 Pe

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the mass of the gas, m__________ (kg)
A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the electrical work done on the gas, Wele__________ (kJ)
An insulated vertical cylinder-piston device contains 0.8 m3 of refrigerant 134a at 1.2 MPa and 120 ° C. With a linear (compression) spring, all of its force is applied to the plunger at that moment. A valve connected to the cylinder opens and refrigerant escapes. The spring is loosened as the plunger is lowered, and the pressure and volume drop to 0.6 MPa and 0.5 m3, at the end of the process. Determine: a) the amount of refrigerant that escaped b) the final temperature of the coolant
An insulated vertical cylinder-plunger device contains 0.8 m ^ 3of refrigerant 134a at 1.2 MPa and 120 ° C. With a linear (compression) spring, all of its force is applied to the plunger at that moment. A valve connected to the cylinder opens and refrigerant escapes. The spring is released as the plunger is lowered, and the pressure and volume drop to 0.6 MPa and 0.5 m ^ 3, at the end of the process.Determine:a) the amount of refrigerant that escaped andb) the final temperature of the coolant
A non-flow reversible process occurs for which pressure and volume are correlated by the expression p = (V2 + 6/V) where p is in bar and V is in m³. What amount of work will be done when volume changes from 3 to 5 m³?
Consider you have an insulated mixing chamber at steady state. This control volume receives two liquid streams at T1 and T2 (with mass flow rates of m1,and m2) and delivers a single stream as an output at T3 and m3.Use the incompressible substance model (with constant specific heat c), neglect the kinetic and potential energy effects, and obtain an expression for T3 in terms of T2, T1 and m1/m3.
a tank of volume 1m3 initially contains steam at 60 bar 320 degrees celsius . stream is stream withdrawn slowly form the tank until the pressure drops to 15 bar. An electronic resistor in the tank transfers energy to the steam maintaining the temperature constant at 320degree Celsius(c) during the process. Neglecting kinetic and potential effects, determine the amount of entropy produced in kj/k
A Piston-Cylinder system initially contains R-134a refrigerant at a temperature of 2.8 bar and 40°C and an initial volume of 0.1 m3. First, heat is transferred to the system by keeping the piston constant and this process is continued until the pressure is 3.2 bar. The process is then maintained by allowing the volume to change while the pressure is kept constant. At the end of this process, the temperature reaches 50°C. Assuming the state changes as if they are balanced,calculate;a) The mass of R-134a refrigerant in the system,b) The amount of heat transferred during the fixed volume process,c) The amount of heat transferred during constant pressure operation.d) Show the state changes on the P-v diagram.
An oxygen gas R = 0.2598 KJ/kg°k and k = 1.395. If 4 kg of oxygen undergo a reversible non flow constant pressure process from initial volume =1.2 cubic meter and initial pressure = 690 kPa to a state where final temperature = 600°C. What is the initial temperature ? Determine the constant volume specific heat. Determine the constant volume specific heat. Determine the Change in Internal Energy. Determine the constant pressure specific heat. Determine the Change in Enthalpy.
Ten kg of water 45 °C is heated at a constant pressure of 10 bar until it becomes superheatedvapour at 300°C. Find the change in volume, enthalpy, internal energy and entropy.
A frictionless piston-cylinder assembly initially contains saturated liquid water at a pressure of 200 kPa. Then, 450 kJ of heat transfer occurs from a source with a temperature of 500 0C to water and some of the water evaporates at constant pressure. Show whether this state change is feasible or not by considering the increase of entropy principle.
Ammonia in a piston-cylinder device initially at 7bar,30°C undergoes a reversible isothermal compression process until the volume is reduced to 25% of the initial volume. a) Draw the process T-s and p-v-diagrams, relative to saturation lines. b) What is the heat and work per unit mass?