Q4: An anulog voltage (0 to 5) volt is to be converted to 8 bit digital form. a. What is the resolution in volt. b. What is the digital representation of 2.2 volt. c. What is the largest quantization error as a percentage to full scale. d. What is the error made in quantization of 2.2 volt as a percentage of the input.

Q4: An anulog voltage (0 to 5) volt is to be converted to 8 bit digital form. a. What is the resolution in volt. b. What is the digital representation of 2.2 volt. c. What is the largest quantization error as a percentage to full scale. d. What is the error made in quantization of 2.2 volt as a percentage of the input.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

The current output of a successive approximative type ADC is showing as 110011. If the reference voltage to the ADC is 5V, what is the corresponding analog signal voltage input to this ADC? If the ADC were of 10 bits, would the conversion time be reduced? Please answer ASAP I will like it please ASAP...
Which statement describe a digital signal? a. is a smoothly and continuously varying voltage or current. b. will take on finite set of voltage levels. c. take on all possible values of amplitude. d. can have an infinite number of values in a range
(II) Consider a rather coarse 4-bit analog-to-digital conversion where the maximum voltage is 5.0 V. (a) What voltage does 1011 represent? (b) What is the 4-bit representation for 2.0 V?
Q1) List the main internal elements of a microcontroller. And explain the function of each of them. Q2) What is the difference between the Von-Neuman Microcontroller Architecture and Harvard Microcontroller Architecture. Q3) Compare between the (EEPROM) and the Non-Volatile RAM - (NVRAM). Q4) What is the term “Complex Instruction Set Computer(CISC)” mean in the Microcontroller Architecture.
Qَ\ discuss a conversion of an analogue signal to digital bits Please I need to resolve the question quickly
Q1: Design and implement an asynchronous counter that counts from 0000 up to 1100 (modulus 13). Use OR gate, and show in the drawing how the OR gate is connected to truncate the state 1101.
1- What does the VOH parameter of a logic IC refer to? a) The highest permissible output voltage. b) The lowest output voltage recognized as logic 1. c) The highest output voltage recognized as logic 1. d) The highest output voltage recognized as logic 0. 2- Which of the following refers to the noise margin of a logic gate? a) The difference between VIH and VOL b) The difference between VOH and VOL c) The difference between VOH and VIH d) The difference between VIH and VIL 3- How many 74LS00 NAND gate inputs can be driven by a 74LS00 NAND gate outputs Refer to data sheet of 74LS00, the maximum values of IOH = 0.4 mA, IOL = 8 mA, IH = 20 μA, and IL = 0.4 mA. 4- The data sheet of a quad two-input NAND gate specifies the following parameters: IOH (max.) 0.4 mA, VOH (min.) 2.7 V, VIH (min.) =2V, VIL (max.) 0.8 V, VOL (max.) 0.4 V, IOL (max.) 8 mA, IL (max.)=0.4 mA, IIH (max.)-20µA, ICCH (max.) 1.6 mA, ICCL (max.) 4.4 mA, tpLH =pHL=15 ns and a supply voltage range of 5…
Given a 5-bit ADC with the following reference values Vref= -2V and 12V, what is the voltage represented by the output sequence 01010?
A frequency counter is gated on for 10 ms and counts 540 pulses from a periodic input signal . What is the input frequency? a) If the gate time is changed to 100 ms , approximately how many counts would you expect from the same source during the gate time? b) In what way does the change in the gate time affect the resolution?
Explain the functions of decoders and multiplexers. Then given at least two examples of applications for both of them.
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
Explain each component of the block diagram of a frequency counter. - Input: - Accurate time-base / clock: - Decade dividers and flip-flop: - Gate: - Counter/ latch: - Display: