Q4. A beam carries a concentrated load, W kN and 2W kN at point A and at point C, respectively as shown in Figure Q4(a). Figure Q4(b) shows the crosssectional view of the beam. The moment of inertia of the cross-section to the x-axis is Ix = 56.27 x 106 mm4. (a) (b) (c) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam in terms of W. What is the safe value of W, can be applied to the beam if the allowable bending stress in tension is 60 N/mm² and allowable bending stress in compression is 100 N/mm². By using the value of W obtained from Q4(b), determine the maximum shear stress of the beam at the maximum shear force. FIGURE Q4(a) W KN A B 2 m +2m² + 71 mm 129 mm 4 m 2W KN 175 mm 4 m D 50 mm Neutral axis FIGURE Q4(b)

Q4. A beam carries a concentrated load, W kN and 2W kN at point A and at point C, respectively as shown in Figure Q4(a). Figure Q4(b) shows the crosssectional view of the beam. The moment of inertia of the cross-section to the x-axis is Ix = 56.27 x 106 mm4. (a) (b) (c) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam in terms of W. What is the safe value of W, can be applied to the beam if the allowable bending stress in tension is 60 N/mm² and allowable bending stress in compression is 100 N/mm². By using the value of W obtained from Q4(b), determine the maximum shear stress of the beam at the maximum shear force. FIGURE Q4(a) W KN A B 2 m +2m² + 71 mm 129 mm 4 m 2W KN 175 mm 4 m D 50 mm Neutral axis FIGURE Q4(b)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The shear force of the beam,whose loading and span conditions are given in Figure 1, and draw bending moment diagrams q=2 kN/m P=27kN M=6kN L1=2.5m L2=1.5m
Figure shows a simply supported beam that is loaded with the point loads of 100 kN at B and C. The cross section of the beam is showm in the figure. Determine the maximum shear and moment along the beam.
For the steel rigid frame in Figure P8.31, com- pute the rotation of joint B and the horizontal displace- ment of support C. Given: E = 200 GPa, A = 500 mm2 , I = 200 × 106 mm4
The simply supported beam in the figure is loaded by the clockwise moment 10 kN-m at B. Draw the shear force and bending moment diagrams by area method. Neglect the weight of the beam.Show complete solution with FBD
The simply supported beam in the figure is loaded by the clockwise moment 10 kN-m at B. Draw the shear force and bending moment diagrams by area method. Neglect the weight of the beam.Please show complete solution
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.
A truss is loaded with nodal force at C as shown TOS-003. If the truss members have identical rectangular section of 5 cm x 8 cm, with E = 70 GPa, compute the vertical displacement at joint C .
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.2 ft, b = 3.3 ft, P = 22 kips, and w = 2.7 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
1) Draw the shear force and bending moment diagram of the beam in Figure Q2(a), (b), and (c). The dimension of the beam are as shown in Figure Q2(a).
(a) Figure Q2 shows a frame with tie rod at joint B and C. The beam carries a concentratedload 300kN at span BC. Analysis and sketch the shear force and bending-momentdiagram for the entire frame.
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 4.5 ft, P = 21 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.