Q5) For unity feedback control system with forward transfer function (G(s) ):G(s) =; By using root locus graph calculate the valueK(s+5)(s+2)(s²+12s+50)of gain (K) which must be added to get the dominant root at damping ratio(-0.886) and natural frequency (w = 8 rad/sec )?wwwCTRICALENGIN

Transfer function:Pole locations:

Answered: Q5) For unity feedback control system…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.6P

See similar textbooks

Similar questions

a)is the aircraft stable about the equilibrium represented by the transfer function? b) Using proportional feedback,what is the range of acceptable gains for the closed loop systen to be stable? c) Design a feedback control system that allows the pilot to command a pitch angle with overshoot less than or equal to 4.15% and a natural frequency of greater than or equal to 0.99 rad/s d) Design a feedback control system that allows the pilot to command a pitch angle with the same overshoot and a natural frequency of one half the system in part c.
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
A stock-flow system models the level of water in a lake. Near a certain equilibrium point, there are three feedback loops: an amplifying feedback loop with strength of +0.55 per month, a stabilizing feedback loop with strength of -0.09 per month, and an amplifying feedback loop with strength of +0.79 per month. Calculate the strength of the overall feedback.
The satallite system below is controlled using reaction wheels. The torque wheel input for the system is u(s) and the satallite attitude is Ө(s) For a strong communication link Ө needs to be a value where the satallite atenna is pointing at the ground station The transfer function for this system will be shown in the picture. Design a feedback control system that sets the closed loop damping ratio at 0.8 and the natural frequency is at 10 rad/sec.
Calculating the separation and / or joining angles in the negative feedback control circuit, if any, given as Controlling (K) and Controlled G (s) = (s + 1) / (s2-4 * s + 5) Explanation: The roots of the equation (s2-4 * s + 5); s1 = 2 + 1 * j and s2 = 2-1 * j and the system Transfer Function is TF (s) = K * G (s) / (1 + K * G (s)). a. There are split angles up to (+108.435) and (-108.435) b. There are split angles as much as (+71,565) and (-71,565) c. There are conjunction angles of (+90) and (-90). D. There are separation angles as much as (+18.435) and (-18.435). E. There are no separation and convergence angles.
A vibrating spring-mass system has the feedback control system shown in Fig Q3 below. (figure attached as image ACT)If K = 12.25 determine:6.1 the transfer function ; (3)6.2 the characteristic equation with a impulse input; (1)6.3 the un-damped natural frequency of the system; (2)6.4 the damping ratio; (2)6.5 the damped natural frequency; (2)6.6 the maximum percentage overshoot; (2)6.7 the peak time; (1)6.8 the settling time for the response within 2%. (2)
1.block diagram physical meaning and the time response for different inputs
The engine, body, and tires of a racing vehicle affect the acceleration and speed attainable. The speed control of the car is represented by the model shown in Figure 2. (i). Determine the steady-state error of the system with unity gain and explain with suitable justification about the system type. A= 12 , B=5 , C=10 , D= 16 (ii). Determine the static error coefficient associated with the system. (iii). Assume the steady state error to be 10%. What will be the value of the controller gain, K?
Graph/Plot the output step response from t=0 to t=10 with a 0.1-second interval.
EXPERIMENT TITLE : PID CONTROLLER IN LEVEL CONTROL SYSTEM OBJECTIVE:To demonstrate the characteristic of P,PI and PID controller response on a level controller system. Based on the topic and objective given,please make a clear introduction.
Name two effects of negative feedback.
A Block diagram of a feedback control system is shown in Figure Q3. Using the Block Diagram Reduction Method, solve for the output Y(s) when:(i) Input D(s) = 0,(ii) Input R(s) = 0,(iii) Input R(s) and D(s) are both applied (i.e., R(s) ≠ 0 , D(s) ≠ 0).

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

SEE MORE TEXTBOOKS

Q5) For unity feedback control system with forward transfer function (G(s) ): G(s) = ; By using root locus graph calculate the value K(s+5) (s+2)(s²+12s+50) of gain (K) which must be added to get the dominant root at damping ratio (-0.886) and natural frequency (wa - 8 rad/sec )?