73ll a O ...simple23.5%epicyclicnone of these76.5%Q5:- The purpose of the idler gearin a gear train is:-17 responsesTo connect gearswhere a largecenter distanceis available.82.4%None of these.To control thedirectionalrelationshipbetween the first17.6%and last gears.This content is neither created nor endorsed by Google.Report Abuse - Terms of Service - Privacy PolicyGoogle Forms

Answered: Q5:- The purpose of the idler gear in a…

Engineering

Mechanical Engineering

Q5:- The purpose of the idler gear in a gear train is:-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select a conventional ICE (Internal Combustion Engine) passenger car from the market. Convert the ICE powertrain to an electric powertrain using the structural and performance parameters of the vehicle by calculating the electric motor shaft power, torque and speed, sketching the required graphs of the vehicle performance, selecting a proper gearbox ratio, analysing the gradeability performance of the car, selecting a battery pack and define battery voltage, current and energy capacity (Give thereasons of your selection), and defining the performance and energy consumption of the car for a specific drive cycle (calculate the cost of the drive considering the price of electricity too).
You are asked to design a four cylinder four-stroke spark ignition engine for a passenger car, which is required to provide a maximum brake torque of (2.60x10^2) Nm at the rated speed of (7.000x10^3) rpm. To simply the design, the bore (B)/stroke (L) ratio is assumed to be unit, i.e. B=L. Given that the bmep of the engine is assumed to be (7.000x10^2) KPa, find its mean piston speed. The answer should be in the unit of m/s with 3 significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Question 7 options: x10 Answer
Choose the correct answer: - In a set of meshing gears, forces are transmitted on ….. which is normal to the contacting surfaces. a) Pitch angle b) Base circle c) Line of action d) Pitch radius - The pressure line is tangent to which circles of the gear and pinion? a) Pitch circles b) Base circles c) Addendum circles d) Dedendum circles - Which one is correct about brittle materials? a) They show a considerable plastic deformation. b) Distortion energy theory is an acceptable theory to describe the failure in these materials. c) They exhibit catastrophic failure.
Plz answer this in 40 min, i need the answer ASAP,thx mechanical engineering Determine from the image below: 1. Types of gears in below gearbox. 2. module 3. surface width (tooth width), and 4. Outer diameter of pinion and gear.
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
In a six cylinder in-line two-stroke cycle Diesel engine, the cylinders are pitched 150 mm apart. The crank length is 100 mm and the ratio of connecting rod to crank is 4.5. The reciprocating mass per line is 1 kg. The engine speed is 2121 rpm. Two possible firing order for this engine are 1-5-3-6-2-4 and 1-4-5-2-3-6. As a young engineer, you have been tasked to evaluate the most suitable firing order for this engine. Your evaluation should include examination of the engine for balance of primary and secondary forces and couples for the given firing order. Apart from examining the engine, you need to justify why one firing order is superior to the other.
What are the harmful effects of backlash error in gears?
Two spur gears transmit 36kW with a velocity ratio of 2:1. The speed of the smaller driving gear is 100rpm. The centre distance between the shafts is to be as near as possible to 920mm. If m=10 and all-21MPa, determine a) Diameter of the shafts b)PCD for each wheel c)Number of teeth on each wheel d) Actual centre distance [ e) Width of the teeth
why should i choice aluminum alloy over sintered bronze and cast bronze for camshaft bearing ? Relate your answer with the properties of each materials and it availibilty.
The output shaft diameter is typically larger than the input shaft diameter on worm drive gearboxes. Explain why
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
Identify the gear element for which Lewis equation is applied when the gear and pinion are made of same materials. a. None of the given answers b. Pinion whose strength factor is more c. Pinion whose strength factor is less d. Gear whose strength factor is less