TWo ivolule gears IN MESA have 20° presSWre angle. The gear ratio is 3 and the number of teeth on the pinion is 24. The feeth have a module of 6 mm. The pitch line velocity is 1.5 m/s and the addendum egual to one module. Determine the angle of action of the pinion (the angle turned by the pinton when one paIr of teeth is in the mesh) and the maximum velocity of sliding.

TWo ivolule gears IN MESA have 20° presSWre angle. The gear ratio is 3 and the number of teeth on the pinion is 24. The feeth have a module of 6 mm. The pitch line velocity is 1.5 m/s and the addendum egual to one module. Determine the angle of action of the pinion (the angle turned by the pinton when one paIr of teeth is in the mesh) and the maximum velocity of sliding.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.
Two mating spur gear with module pitch of 6.5 mm have 19 ad 47 teeth of 20° pressure angle and 6.5 mm addendum. Determine the number of pair of teeth and angle turned through by the larger wheel for one pair of teeth in contact. Determine also the sliding velocity at the instant engagement commences engagement terminates. When the pitch line velocity is 1.2 m/s. b.) The number of teeth on each of the two spur gears in mesh is 40. The teeth have 20° involute profile and the module is 6mm. If the arc of contact is 1.75 times the circular pitch. Find the addendum.
a pinion has 56.716 teeth of 5.96mm module and runs at 2.265 rev/min with a torque of 39.961N.m. it meshes with a gear wheel which has 124.409 teeth. the gears operate with a pressure angle of 27.61 degrees and a contact ratio of 31.22. If the path of recess is 1.2 times the path of approach, determine the path of recess
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
(Q.1) A compound epicyclic gear is shown in Fig. for Q.1. The shaft P is drivenat 3000 rev/min while the annulus A2 is driven at 1000 rev/min in theopposite direction. The numbers of teeth in the gears are S1, 16; S2,24; A1, 60; A2, 90. Determine the speed and direction of rotation ofshaft Q. (Q.2) A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
Two spur gears of 24 teeth and 36 teeth of 8 mm module and 20° pressure angle are in mesh. Addendum of each gear is 7.5 mm. The teeth are of involute form. Determine : 1. the angle through which thepinion turns while any pair of teeth are in contact, and 2. the velocity of sliding between the teethwhen the contact on the pinion is at a radius of 102 mm. The speed of the pinion is 450 r.p.m
Original Question: The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B QUESTION THAT NEEDS TO BE ANSWERED: For the bevel gear system shown in problem above, determine the angular accelera-tion of gear B when gear A is stationary and member OC has an angular velocityof 10j rad/sec and and angular acceleration of 25j rad/sec2
Two gear wheels with 50 and 30 teeth respectively, mesh externally, the speed of the smaller being 1800 r.p.m. Determine the velocity of sliding between the gear teeth faces at the point of engagement, at the pitch point, and at the point of disengagement if the smaller gear is the driver. Assume that the gear teeth are 18° involute form, addendum length is 8 mm and the module is 5 mm. Also find the angle through which the pinion turns while any pairs of teeth are in contact. answer with clear word please.
in the epicyclic gear, annulus gear B has 120 teeth externally and 100 teeth internally. driver A has 20 teeth and the arms E is connected to the driven shaft. The Sun gear D has 60 teeth. If A revolves at 100 r.p.m clockwise and D revolves at 27 r.p.m clockwise. If gear D is fixed and A transmits a torque of 10 N.m at 100 r.p.m clockwise
Two parallel shafts have an angular velocity ratio of 4 to 1 are connected by gears, the largest of which has 40 teeth. Find the number of teeth of smaller gear.
Consider the epicyclic gear system. Set up a tabke of wheel speeds for the cases where all the wheels rotate..Consider the same system with the sun wheel S as the input and the annulus A as the output.The diameters of the sun andbplanet wheels are 150mm and 75mm,respectively. I the sun wheel runs clockwise at 1000 rev/min and output to input ratio Na/Ns is -1,determine the speeds of the arm L and the planet wheel P.
In an epicyclic gear of the sun and planet type, the p.c.d of the internally toothed ring is tobe as close as possible to 220 mm and the teeth are to have a module of 4. When the ringis stationary, the spider, which carries three planets, is to make one revolution for everyfive of the driving spindle carrying the sun wheel.(a) Determine suitable numbers of teeth for all the wheels. 10(b) Determine the exact p.c.d of the ring 2(c) If a torque of 12 Nm is applied to the shaft carrying the sun wheel, what torquewill be required to keep the ring stationary?