Air at 24°C is blown over a hot pipe with a surface area of 2.94 m2 to dissipate 924 W of heat energy. What is the minimum convection heat transfer coefficient that will ensure that the temperature of the pipe surface is less than 45°C [round your final answer to two decimal places]?

Air at 24°C is blown over a hot pipe with a surface area of 2.94 m2 to dissipate 924 W of heat energy. What is the minimum convection heat transfer coefficient that will ensure that the temperature of the pipe surface is less than 45°C [round your final answer to two decimal places]?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.10P: 3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the...

See similar textbooks

Related questions

Q: A cast-iron beam has the cross-sectional dimensions shown in the figure. If the allowable stresses…

A: Givenσyt=50MPaσyc=250MPaτy=55MPa

Q: a. Determine the diffusion coefficient for zinc diffusing into copper at 200°C. b. Create a plot…

Q: Find the support reactions (Ax, Ay, By) of the given "L" shaped body depicted below. 5[m] 2[m] Ax Ay…

A: According to the given data A loading body We need to find Reactions at support

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: The allowable shear stress is Tallow = 7 ksi. Part A Determine the largest shear force V that the…

Q: A 180-1b man and a 120-lb woman stand side by side at the same end of a 300-lb boat, ready to dive,…

A: According to the given data The weight of the man, Wm=180 lb The weight of the woman, Ww=120lb The…

Q: You are examining two materials with the same density. One has a BCC crystal structure, and one has…

A: Given data:- BCC crystal structure HCP crystal structure. The same density To find:-Which crystal…

Q: Consider the beam and loading shown. Knowing that d = 1.19 in. and E = 29 × 106 psi, determine the…

A: Draw the free-body diagram of the beam.

Q: Determine the force in all members of the truss

A: According to the given data in the question, Considering the free body diagram below We need to…

Q: 3. A refrigerator uses refrigerant-134a as the working fluid and operates on the ideal vapor-…

Q: 7.7 A 2-in.-diameter hole, 5 in. long, is drilled into the center of the top face of a steel cube…

A: According to the given data Cube size=a=6 in d=2 in hole diameter with L=5in from the top That hole…

Q: +1. 6 in. 1 B 4 in. 5 in. A 200 lb D 10 in.- E Draw the free body diagram and calculate reactions at…

A: The given data Load at D = 200lb Draw the free body diagram and reaction at support A and E

Q: QUESTION 3 For the stress element below, when a = 6, b = 6, and c = 3, the maximum shear stress T,…

Q: Ball B is suspended a cord of length attached to cart A, can roll freely on a frictionless,…

Q: In the example of 100 ME students , suppose we only sampled 20 ME students, and we found the sample…

A: To calculate the t-value for a single-sided 95% confidence interval with a sample size of 20, we…

Q: 2. Refrigerant-134a enters the compressor of a refrigerator at 100 kPa and -20°C at a rate of 0.5…

Q: a pump discharges 250 gpm of water at a temperature of 180 fahrenheit against atotal head of 152…

Q: 2.70 kg 3.60 kg 4.00 kg 6.20 kg 7.25 kg none of the above m1 1.00 m m2 A system of two paint buckets…

A: According to the given data u=0 v=2.50m/s h=1m m1=12kg We need to find Mass of the block 2

Q: A trough whose cross section is a semicircle of radius r = 4 m is filled with water. What is the…

A: As per bartleby guidelines, I am going to solve only the first question. Given data: r=4 mg=9.8 m/s2…

Q: 5. Calculate the total hydrostatic force on the gate with width 2.5 m and pivoted at O; D is 3 m…

Q: Q1 A uniform compressible flow occurs in a constant diameter pipe. Write the simplified differential…

A: It is given- Fluid flow in a pipe of constant diameter pipe and it is a compressible flow. It is…

Q: d) An incompressible fluid with density p is flowing through the duct system shown. You may assume…

Q: The brake is to be designed to be self locking, that is, it will not rotate when no load P is…

Q: 4. What length of a square key is required for a 4-in diameter shaft transmitting 1000 hp at 1000…

A: Given:Shaft diameter, D=4 inPower transmission by the shaft, P=1000 hpShaft speed, N=1000…

Q: Q24. For the below figure please write its part program. The depth of the cut is 0.25 inches…

Q: 01Predict the fundamental natural frequency using Dunkerly method k1=10N/m k2=20N/m k3=15N/m m1 =…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 1) Determine the x and y components of force at pin A. Express your answers in kilonewtons to three…

A: According to the given data We need to find Reactions at A and D

Q: A load P is supported by a structure consisting of rigid bar BDF and three identical 15-mm- diameter…

A: Given: A load P is supported by a structure consisting of rigid bar BDF and three identical (d)…

Q: A propped cantilever beam is loaded as shown in Figure P11.13. Assume EI = 200,000 kN·m 2 . Use…

A: GivenA propped cantilever beam EI = 200,000 kN·m2

Q: A B C AAAA D

Q: The crowbar is subjected to a vertical force of P = 25 lb at the grip, whereas it takes a force of F…

Q: The beam in (Figure 1) is made from three boards nailed together as shown. Figure 20 mm 200 mm M 25…

A: Given data :- Bending moment = 460 N-m Find :- The resultant force that the bending stress will…

Q: www Aluminum 10K 12' w w Steel A 12' long beam in supported by an aluminum hanger at A and by a…

A: The given information in the problem is shown in the following attached image:

Q: Determine the normal force, shear force, and moment at point C. Take that P= 12 kN and w=8…

Q: 1.C3 Two horizontal 5-kip forces are applied to pin B of the assembly shown. Each of the three pins…

A: Given: To find: Program to find normal, shear, bearing stresses Permissible diameter

Q: s it necessary to provide CONTINGENCY in your quantification/estimation? Justify your answer.

A: To find: Is it necessary or not to provide contingency in quantification/estimation?

Q: Q1. State whether each of the two statements included in your input values for Q1 are true or false:…

A: We will answer the first question. Please resubmit the question which you would like to be answered…

Q: A 1.5-m-diameter cylindrical tank is formed of 6-mm-thick sheet steel (E = 200 Gpa, ν = 0.3). The…

A: Given: The diameter of tank d=1.5 m=1500 mm The thickness of steel sheet t=6 mm The contents…

Q: circular plate, 50 cm in diameter, is placed vertically in oil of specific gravity 0.9. The center…

Q: Odd side please

Q: 5. The A-36 steel tubular shaft is 2 m long and has an outer diameter of 50 mm. When it is rotating…

A: According to0 the given data The length of the tubular shaft is L=2 m. The outer diameter of the…

Q: A hot wire anemometer was calibrated in an air jet at ambient temperature TO = 26.3 °C and a wire…

A: Given data: ambient temperature, T0 = 26.3 °C Wire temperature, Tw = T = 140 °C Stagnation air…

Q: Unit for Painting Works a. Liters b. Gallons c. Square Meters d. All of the above

A: Painting works refer to the process of applying paint to a surface to protect, decorate, or enhance…

Q: Question 3: The acceleration function of an object doing curvilinear motion is a =…

Q: A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE…

Q: A local farm uses a tractor as a prime-mover for carrying out farm operations such as: plowing,…

A: Draw the given diagram.

Q: FIGURE 4.13 Figure for Problems 4-3 and 4-4. 4-3 Shown in Fig. 4.13 is a vertical-walled storage…

A: (a) Volume stored is calculated as: V=Net volume flow rate ×TimeA×h(t)=(q0-qout)th(t)=(q0-qout)tA…

Q: 3-22 Determine the governing equations for the fluid heights in the tanks for the two-tank systems…

Q: 2. Knowing that the allowable normal stress for the steel used is 24 ksi, select the most eco-…

Q: The solution is cut off and I cannot see it. Please condense to make it more vertical because I…

A: The given information in the problem is shown in the following attached image:

Question

Air at 24°C is blown over a hot pipe with a surface area of 2.94 m² to dissipate 924 W of heat energy. What is the minimum convection heat transfer coefficient that will ensure that the temperature of the pipe surface is less than 45°C [round your final answer to two decimal places]?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a resistance of 310-4 ohm per meter of length. If the air around this line is at v, determine the surface temperature on a windy day, assuming a wind blows across the line at 33 km/h.
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
A 5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a velocity of 50 m/s (h = 180 W/m2 K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 °C. Comment on your calculation.
During a cold winter day, wind at 55 km/h is blowing parallel to a 4m high and 10m long wall of a house. If the air outside is at 5 degrees Celsius and the surface temperature of the wall is 12 degrees Celsius , determine the rate of heat loss from the wall by convection. What would your answer be if the wind velocity has doubled? From Table A-1:thermal conductivity, k = 0.0246 W/m degrees Celsiusviscosity, v = 1.4 x 10^-5 m^2/sPrandtl no. Pr = 0.717
A 5.0-cm-diameter cylinder is heated to a temperature of 200 oC, and air at 30 oC forced across it at a velocity of 50 m/s (h = 180 W/m2K). If the surface emissivity is 0.7, calculate the total heat loss per unit length if the walls of the enclosing room are at 10 oC. Comment on your calculation. COMPLETE SOLUTION
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 3 cm thick. The convection heat transfer coefficient on the upper surface is 30 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = AnswerkJ. b. If the reverse side surface temperature is maintained, determine the hourly heat loss occurring = AnswerkJ.
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 2.5 cm thick. The convection heat transfer coefficient on the upper surface is 40 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = Answer kJ. b. If the reverse side surface temperature is maintained, determine the hourly heat loss occurring = Answer kJ. Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 2.5 cm thick. The convection heat transfer coefficient on the upper surface is 40 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = Answer kJ. b. If the reverse side surface temperature is maintained, determine the hourly heat loss occurring = Answer kJ.
Air at 25 ° C blows over the hot steel plate whose surface temperature is maintained at 150 ° C. The plates are 50 cm x 40 cm in dimensions and 3 cm thick. The convection heat transfer coefficient on the upper surface is 30 W / (m² ° C). The thermal conductivity of steel is 45 W / (m ° C). Calculate the hourly heat loss from the plate surface. a. heat loss per hour = ..... kJ. b. If the reverse side surface temperature is maintained, determine the hourly heat loss occurring = ..... kJ.