Q5. The magnetization curve for a certain self-excited, 125-V,50-kW, 1750 r/min shunt generator is shown in Figure 1, Theno-load voltage with the rheostat shorted is 156 V. Determine:[12](i) field-circuit resistance(ii) field-rheostat setting that will provide a no-load voltage of140 V(iii) Armature voltage if the rheostat is set lo 14.232(iv) Field-rheostat setting that will cause critical resistance(v) Armature voltage at 80 percent rated speed, and therheostat shorted(vi) Rheostat setting required to obtain a no-load armaturevoltage of 140 V at 1750 rpm if the shunt field isseparately excited from a 120-V DC source1750 rfmin160Crikicalresistance140lineS0% speed120100Field resistance LineRheostat shorted604020Shunt-Field Carrent Iy (A)FIGURE 1Exampie 12.1Generated EMF E (V)

Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q5. The magnetization curve for a certain self-excited, 125- V,50-kW, 1750 r/min shunt generator is shown in Figure 1, The no-load voltage with the rheostat shorted is 156 V. Determine: [12] (i) field-circuit resistance (ii) field-rheostat setting that will provide a no-load voltage of 140 V (iii) Armature voltage if the rheostat is set lo 14.232

Q5. The magnetization curve for a certain self-excited, 125- V,50-kW, 1750 r/min shunt generator is shown in Figure 1, The no-load voltage with the rheostat shorted is 156 V. Determine: [12] (i) field-circuit resistance (ii) field-rheostat setting that will provide a no-load voltage of 140 V (iii) Armature voltage if the rheostat is set lo 14.232

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The output of a shunt generator is 66 A at 100 volts. Armature and field resistances are, respectively, 0.04 ohm and 25 ohms. If the efficiency at this load is 88%, determine the core and friction losses
An 8-Pole, simplex lap wound, shunt generator has 800conductors and a flux per pole of 0.025Wb and running at 1200rpm. The armature and shunt field resistances are 0.25Ω and 120Ω respectively. If the armature voltage drop is equal to 10V, what is the load current (in Amp)? use two decimal places if the answer is not exact and do not include the unit anymore.
- A separately excited 4 - pole, 900 rpm wave wound dc generator has an induced emf of 240V at rated speed and rated field current. When connected to a load, the terminal voltage is observed to be 200V. If the armature resistance is 0.2 Ω and the flux per pole is 10 m Wb, compute the armature current and the number of conductors
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
An 8 pole DC shunt generator with wave winding has 4800 conductor with 20 turns and average per pole flux is 20 mwb and armature current and armature resistance is 20 A and 0.5 ohm respectively find? (i) Induced emf (ii) Terminal voltage
A 500-V, wave-wound, 750 r.p.m. shunt generator supplies a load of 195 A. The armature has 720 conductors and shunt field resistance is 100 Ω. Find the demagnetising amp-turns/pole if brushes are advanced through 3 commutator segments at this load. Also, calculate the extra shunt field turns required to neutralize this demagnetisation.
4. A short shunt compound generator supplies a load of 10 kW at 200 V through a pair of feeder resistance of 0.10 ohm. Armature, shunt field resistance and series field resistance are 0.10 ohm, 52.5 ohms and 0.10 ohm, respectively. If the core, friction, and windage losses amount to 631 watts, determine (a) HP of driving engine (b) commercial, electrical and mechanical efficiencies.
The following sequential statements, when completed, describe armature reaction in a DC generator. Complete each statement by inserting the appropriate word from among those provided in the word list below. Notes: A word may be used more than once. There are more words than required. Word list:armature, between, brushes, clockwise, commutator, currents, direction, distortion, increase, induces, inline, interpoles, main-field, neutral-plane, power, rotating, rotation, slip-rings, slow-down, sparking, speed, torque, voltage. The effects of armature reaction can be reduced by equipping the DC machine with _________________ connected in series with the _______________, or by physically shifting the position of the __________________. If this is not done _______________ will occur at the brushes and the generator output ________________ will be reduced. Prolonged operation in this state can lead to sustained damage to the brushes and _________________.
please answer in bond paper 3. A long-shunt, four pole, 1500-W, 250-V, duplex wave-wound DC compound generator with the rated speed of 500 r.p.m., has a shunt field resistance of 100 Ω, a series field resistance of 0.05 Ω and an armature resistance of 0.2 Ω. If the flux per pole is 48.798 mWb and a total of 620 conductors, calculate the following: (a) the generated voltage, (b) the field currents, (c) the power generated in the armature.
A 150 kW, 250-volt compound DC generator has its field windings which are connected in long shunt. If the shunt-field winding resistance is 20 ohms, what is the current in the series-field winding? (Note that the series field resistance is connected in series with the armature.)
Of a shunt excited DC generator, Excitation winding internal resistance Rf = 2.5 Ω Armature winding internal resistance Ra = 0.5 Ω A rheostat has been placed in the excitation circuit to keep the machine's end voltage constant at Va = 30 V. Machine Voltage magnetization induced in the armature while operating at n = 1400 rpm at If = 7 A excitation current It is determined as Ea = 30 V from its characteristic. According to this, a) With peak voltage Va = 30 V, excitation current If = 7 A, power supplied to the load when the speed n = 1400 rpm What is the resistance of the rheostat? b) Spindle revolutions are reduced to n = 1000 rpm. In this case Va = 30 V and Ea = 37 V constant What value should the rheostat be adjusted to keep it? Calculate the power given to the load in this new case.
A 1500 kW, 550 V, 16 pole generator runs at 150 rev. per min. What must be the useful flux if there are 2500 conductors lap-connected and the full-load copper losses being 25 kW? Calculate the area of the pole shoe if the gap density has a uniform value of 0.9 wb/m2 and find the no-load terminal voltage, neglecting armature reaction and change in speed.