Q6/ A, B and C three reservoirs have water levels are 300, 250 and 200 m as shown in figure, find the discharge flow in pipes AJ, JB and JC. Take f = 0035 for all pipes. Pipes lengths and diameters are Pipe A 20 Km, 300 mm, Pipe B 10 Km, 220 mm and pipe C 7 Km, 200 mm respectively. Also, Za, Zb and Ze are 300, 250 and 180. В

Q6/ A, B and C three reservoirs have water levels are 300, 250 and 200 m as shown in figure, find the discharge flow in pipes AJ, JB and JC. Take f = 0035 for all pipes. Pipes lengths and diameters are Pipe A 20 Km, 300 mm, Pipe B 10 Km, 220 mm and pipe C 7 Km, 200 mm respectively. Also, Za, Zb and Ze are 300, 250 and 180. В

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
Find an expression for the velocity of water leaving the sprinkler. Find an expression for the gauge pressure at point A, a distance L1, upstream of the narrow pipes. Express the answer in terms of the flowrate, Q. The inner diameter of the first segment of the pipe is d1=10mm, the inner diameter of the second set of pipes is d2=1mm, with N=25. The flowrate through the sprinkler is Q=0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds 2000. Comment on the accuracy of the assumption that the flow could be treated as laminar everywhere. May be assumed water has a density of 1000kg/m^3 and a viscosity of 1mPa s.
A pipe inclined at 45° to the horizontal (Fig. 2) converges over a length l of 2 m from a diameterd1 of 200 mm to a diameter d2 of 100 mm at the upper end. Oil of relative density 0.9 flowsthrough the pipe at a mean velocity ?̅1 at the lower end of 2 m/s. Find the pressure differenceacross the 2 m length ignoring any loss of energy, and the difference in level that would beshown on a mercury manometer connected across this length. The relative density of mercury is 13.6 and the leads to the manometer arefilled with the oil.
The large reservoir in the following figure provides water for the indicated tank with a flow rate of 10 L/s. Check that the machine is installed and a pump or a turbine, and determine its power, if the yield is 75%. Suppose ideal fluid. Data: γH20 = 104N/m3 ; ATubes = 10mc2 ; g = 10m/s2 .
The diameter of a pipe changes gradually from 75 mm at a point A, 6 m above datum, to 150 mm at B, 3 m above datum. The pressure at A is 103 kPa and the velocity of flow is 3.6 m/s. Neglecting losses, with the aid of a neat sketch, determine the pressure at B
at point a in pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity is 1m/s. at point B, 2m higher than A, the diameter is 0.5m and the pressure is 20kPa. Determine the direction of flow. need answer please
the open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V2 for the given data V1 = 3 m/s and Q3 = 0.01 m3/s.
In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
Water at 20°C flows through the orifice in Fig. ,which is monitored by a mercury manometer. If d = 3 cm,(a) what is h when the flow rate is 20 m3/h and (b) what isQ in m3/h when h = 58 cm?
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
Figure 1) shows a tank of 20∘C water with a nozzle h = 27 cm below the surface. Bernoulli's equation applies to the flow between points 1 and 2 on the streamline, but not to the flow between points 2 and 3.What is the volume flow rate through the nozzle in L/min ? Assume that the water level in the tank is held constant.
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider a venturi with a throat-to-inlet area ratio of 0.8, mounted on theside of an airplane fuselage. The airplane is in flight at standard sea level.If the static pressure at the throat is 2100 lb/ft2, calculate the velocity ofthe airplane.