V₁ X = 31 Figure Q3 The figure Q3 shows a 180° elbow. Oil enters this elbow at a speed of X m/s and is discharged into the atmosphere at the exit. Here X is the sum of all the digits of your URN. Inlet area of the elbow is 25m² and outlet area is 10m². If the gauge pressure at the inlet to the elbow is 15 kPa, calculate the horizontal component of force required to hold the elbow in place.

V₁ X = 31 Figure Q3 The figure Q3 shows a 180° elbow. Oil enters this elbow at a speed of X m/s and is discharged into the atmosphere at the exit. Here X is the sum of all the digits of your URN. Inlet area of the elbow is 25m² and outlet area is 10m². If the gauge pressure at the inlet to the elbow is 15 kPa, calculate the horizontal component of force required to hold the elbow in place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a 2.5 inch fire hose discharge a 1.25 inch jet. If the head lost in the nozzle is 6 ft, what gage pressure must be maintained at the base of the nozzle to throw a stream to a vertical height of 100 ft, neglecting air resistance? *please include its figure
The open stream of water seen in the following picture emerges from a nozzle into the atmosphere at sea level, where it then collides with a stagnation tube. If we exclude losses and assume that the pressure at the centerline of section 1 is 110 kPa, we can estimate that the (a) the mass flow measured in kilograms per second (kg/s), and (b) the height, measured in meters, of the fluid in the stagnation tube.
6.36 This two-dimensional water (at 50°F) jet is deflected by the two-dimensional vane, which is moving to the right with a speed of 60 ft/s. The initial jet is 0.30 ft thick (vertical dimension), and its speed is 100 ft/s. What power per foot of the jet (normal to the page) is transmitted to the vane? See §6.5 for useful knowledge about moving CVs.
Consider the flow of a fluid at speed v0, through a cylindrical pipe of radius r. What would be the speedof this fluid at a point where, because of a constriction in the pipe, the fluid is confined to a cylindricalopening of radius r/4?
the open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V2 for the given data V1 = 3 m/s and Q3 = 0.01 m3/s.
Water flows through a circular pipe with a constant radius of 10cm. The speed and pressure at point A is 4m/s and 250,000Pa respectively.a. What is the speed of the fluid at Point B? b. What is the pressure at point B which is 10m higher than point A?
A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction ofmotion and leaves it at 150° absolute with the direction of motion. The absolute inletvelocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore frictionacross the vanes. Calculate:1. the vane outlet angle.
Question : Water flows through a circular nozzle, exits into the air as a jet, and strikes a plate, as shown in the figure. The force required to hold the plate steady is 75 N. Assuming steady, frictionless, one-dimensional flow, estimate Part (a) the velocities at sections (1) and (2) and Part (b) the mercury manometer reading h.
Find the pressure head at entry of the pipe, when the pressure of flowing fluid is 275 N/cm? The pressure head at entry (Unit in Pascal)?
RATE WILL BE GIVEN A jet of water 50 mm in diameter and a plate strikes each at a right angle. When the plate is moving towards the jet at a certain speed, the plate experiences a force that is 2688 N. When that plate is moving away from the jet at the same speed, the plate experiences a force that is 332 N. 1. What is the velocity of the water (m/s) 2. What is the velocity of the plate (m/s) 3. What is the force if the plate stopped moving (N)
A 3.3-in.-diameter pipe carries 338 gal/min of water at a pressure of 27.7 psi. Determinea) the pressure head in feet of waterEnter your answer for part (a) in accordance to the question statement ftb) the velocity headEnter your answer for part (b) in accordance to the question statement ftc) the total head with reference to a datum plane 21.5 ft below the pipeEnter your answer for part (c) in accordance to the question statement ft
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.