I need the answer as soon as possible Q2/ Consider the conical water tank system shown below. The flow through the valve isturbulent and is related to the head (h) by:q = 0.008 h*Where q: is the flow rate measured in (m'/sec).h: is the head measured in (m).Suppose that the head is (3 m) at (t = 0). What will be the head at (t = 1 min)?2m4mdon domping ? ifves

We have the given data asTurbulent value related to head (H) Q=0.008HQ=Measured in m3/sH-meterHead=…

Q2/ Consider the conical water tank system shown below. The flow through the valve is turbulent and is related to the head (h) by: q = 0.008 Vh* Where q: is the flow rate measured in (m/sec). h: is the head measured in (m). Suppose that the head is (3 m) at (t = 0). What will be the head at (t = 1 min)? 2m 4m

Q2/ Consider the conical water tank system shown below. The flow through the valve is turbulent and is related to the head (h) by: q = 0.008 Vh* Where q: is the flow rate measured in (m/sec). h: is the head measured in (m). Suppose that the head is (3 m) at (t = 0). What will be the head at (t = 1 min)? 2m 4m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider the pipe system in the diagram below. Tank 1 is a closed tank and the pressure in tank 1 is kept constant at 200kPa. The water level in tank 1 is at 1.5m. You as an engineer are required to install a frictionless pipe between points A and B. Analyze the system and determine what is the maximum length of pipe would you recommend between A and B? The following conditions are applicable The gravitational acceleration is 9.81m/s2. The minimum required flow rate is 0.5m3/s. The atmospheric pressure is 85kPa. The water in the tank is saturated water with a density of 997kg/m3. The pipe inlet and outlet are both sharp-edged.
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
A fountain and a water tank will be powered by water from a nearby lake. The elevations and pipe connections are depicted in the diagram below. The fountain's jet water should reach a height of at least 2.5 m from the nozzle outlet. The tank, on the other hand, is elevated to allow gravity to distribute water. The table below contains the specifications for nozzles, suction and discharge pipes. What is the minimum power input to the pump in kW, assuming negligible minor head losses? Assume that the pump efficiency is 88 percent and the motor efficiency is 95 percent. The fountain's water is returned to the lake via a drainage system.
4. Brine (SG = 1.1, viscosity = 1.1cP) is pumped at a rate of 45 ft^3/min (ID = 2.5in) from large open reservoir to the bottom of another open tank. The liquid level in the reservoir is maintained at 5.2ft, and the liquid level in the reservoir and the bottom of the discharge tank are 18ft apart, vertically. Friction losses in the pipe amount to 10% of the elevation head. If 2.15 hp of power is required for the process, what is the expected liquid level in the receiving tank?
The plunger diameter of a single acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10,3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 2.1 Find the maximum allowable speed to operate the pump 2.2 What power is expected in overcoming friction at this speed, take f=0.01
Suppose a u-bend is redirecting a flow of water. The water enters flowing to the right at 10 m/s. The u-bend completely reverses the direction of the flow, so the water leaves flowing to the left. The area of the u-bend is constant, a circular cross-section of 0.12 m. The pressure in the fluid is measured at 50 kPa. The length of the u-bend is 0.46 m. Find the force, including magnitude and direction, to hold the u-bend in place.
A 2-1/2 inch fire hose discharges water through a nozzle having a jet diameter of 1 inch. Thelost head in the nozzle is 5.76 percent of the velocity head in the jet. If the gage pressure atbase of nozzle is (a) 86 lb per sq in.: (b) 167 lb per sq in.: (1.1) compute the discharge ingallons per minute: (1.2) what is the maximum horizontal range to which the stream can bethrown, neglecting air resistance?
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity of air flowing if density is 1.16kg/m3.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
For the flow configuration shown, you are required to design a pump station to transfer water from the bottom tank to the upper tank. In your own words, explain the steps that are needed to be followed for the design of the pump system. Your answer should be typed and not more than one page. The pipe equivalent roughness is 1.5 mm. And a valve with a k=10 is located just upstream of the lower reservoir (other losses are negligible). Take p=1000 kg/m”, g = 9.81 m/s?, and u = 1.179 x 102 kg/m.s.
In a venturemeter used for measuring the flow of oil (S = 0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical U tube containing mercury. If the difference level between the fluids in the U-tube arms is (x +1/S.N ) in cm, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.