Q6/ A differential band brake has a force of 220 N applied at the end of a lever as shown in Figure. The coefficient of friction between the band and the drum is 0.35 The angle of lap is 180°, Find the maximum and minimum tension in the band, when a torque of 600 N-m is applied to the drum which rotates clockwise. L150 220 N B w m 100- 200 All dimensions in mm. (Good Luck) دحسن حمودي مهدي مدرس المادة AASO 201 minT bns MJ asaasm A MD mos

Q6/ A differential band brake has a force of 220 N applied at the end of a lever as shown in Figure. The coefficient of friction between the band and the drum is 0.35 The angle of lap is 180°, Find the maximum and minimum tension in the band, when a torque of 600 N-m is applied to the drum which rotates clockwise. L150 220 N B w m 100- 200 All dimensions in mm. (Good Luck) دحسن حمودي مهدي مدرس المادة AASO 201 minT bns MJ asaasm A MD mos

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The figure shows an internal rim-type brake having an inside rim diameter of 11in and a dimension R of 3.5 in. The shoes have a face width of 1.25 in. Find the braking torque and the maximum pressure for each shoe if the actuating force is 205 Ibf, the drum rotation is counterclockwise, and f=0.32. The maximum pressure on the right-hand shoe parp is [ 16.99] @ psi. The maximum pressure on the left-hand shoe pa| H is [100.813 | @ psi. The torque on the right-hand shoe Tgis [ .056 | @ kipin. The torque on the left-hand shoe T is [ .332| @ kipin. Total braking torque Tiotal s [-3887] @ Kip-in.
For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and dimension a = 90 mm. The shoes have a face width of 30 mm. The force exerted by the cylinder hydraulic is 1000 N and the average coefficient of friction is 0.3. Determine: a) The maximum pressure in each shoe; b) The braking torque; c) Reactions resulting from the pivot pin;
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
A differential band brake is shown in the figure. The diameter of the drum is 800 mm. The coefficient of friction between the band and the drum is 0.3 and the angle of embrace is 240°. When a force of 777 N is applied at the free end of the lever, find: a. The maximum force, in Newtons, in the band for the clockwise rotation of the drum b. The minimum force, in Newtons, in the band for the clockwise rotation of the drum c. The maximum force, in Newtons, in the band for the counter clockwise rotation of the drum d. The minimum force, in Newtons, in the band for the counter clockwise rotation of the drum e. The torque which can be applied by the brake, in N-m, for the clockwise rotation of the drum.
1. A double square thread power screw has a pitch of 6 mm and mean radius of34 mm. If it is used to lift a load 50 kN and coefficient of friction of threads is 0.15, determine the torque required toturn the screw.A. 343.74 N-m B. 353.47 N-m C. 335.47 N-m D. 347.35 N-m2. A lubricated bolt needs an initial torque of 145 lb-ft to take the initial tension brought by the compressor withoutbreaking. Determine the initial torque needed by the bolt if the bolt was not lubricated.A. 107.85 lb-ft B.108.25 lb-ft C. 108.75 lb-ft D. 193.33 lb-ft
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
The block brake, as shown in the figure, provides a braking torque of 376 N-m. The diameter of the brake drum is 258 mm. The coefficient of friction is 0.3. Find: a. The force (P), in Newtons, to be applied at the end of the lever for the clockwise rotation of the brake drum b. The force (P), in Newtons, to be applied at the end of the lever for the counter clockwise rotation of the brake drum; and c. The location of the pivot or fulcrum, in mm, to make the brake self-locking for the clockwise rotation of the brake drum.
In the figure, a flexible belt runs from A over the compound pulley B & back over P to a 200-N weight. The coefficient of friction is 1/π between the belt & the compound pulley P. Find the maximum weight W that can be supported w/out rotating the pulley P or slipping the belt on the pulley P.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
The width of the simple band brake shown in the figure is 30 mm. The coefficient of friction between the brake and the drum surface is 0.20. Determine the braking torque and thickness of the band if the tensile stress is not to exceed 65 N/mm2.
(2) A single square thread jackscrew has 2.0TPI. It is to lift 15 tons. The friction radius of the collar is 1-in. The coefficient of friction between the threads and screws and base is 0.15, that between the screw and collar is 0.13. Determine: (a) the diameter of the root of the screw if the allowable stress in compression is 6,000psi; (b) the pull required at the end of 5.0ft bar to raise the load; (c) the twisting moment exerted at the root of the threads; (d) the efficiency of the screw and collar.
A flat belt with a width of 120 mm and a thickness of 5 mm transmits power from a driving pulley with a diameter of 250 mm to a driven pulley with a diameter of 700 mm. The mass per unit length of the belt is 2.1 kg/m, and the coefficient of friction is 0.25. The input power of the belt is 60 kW at 1000 rpm. Calculate the following when the center distance is 3.5 m. (a) Maximum tensile stress of the belt(b) Axial load on each pulley