For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and dimension a = 90 mm. The shoes have a face width of 30 mm. The force exerted by the cylinder hydraulic is 1000 N and the average coefficient of friction is 0.3. Determine: a) The maximum pressure in each shoe; b) The braking torque; c) Reactions resulting from the pivot pin;

For the drum brake shown in the following figure, there is an inner rim diameter of 280 mm and dimension a = 90 mm. The shoes have a face width of 30 mm. The force exerted by the cylinder hydraulic is 1000 N and the average coefficient of friction is 0.3. Determine: a) The maximum pressure in each shoe; b) The braking torque; c) Reactions resulting from the pivot pin;

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter37: Clutches

Section: Chapter Questions

Problem 14RQ: The surface of the pressure plate contacts the. a. transmission main shaft b. throwout bearing c....

See similar textbooks

Similar questions

A car has hydraulically operated disc brakes at the front and drum brakes at the rear. The frontbrakes have pistons of 58 mm diameter each, whereas each of the wheel cylinder at the rearbrake has 28 mm diameter. The master cylinder piston has diameter of 40 mm. The brake footpedal has a leverage of 4. If the brake pedal is applied a force of 100 N, Calculate (i) The brakingforce on the front axle, (ii) The braking force on the rear axle.
An older Rolls Royce Ghost is traveling at 25 mph on a roadway with good, dry pavement.The car has a C D = 0.32, 35 ft 2 of frontal area, and weighs 5,445 lb. The wheelbase is 129.7 inand the center of gravity is 25 in above the pavement and 60 in behind the front axle. Thevehicle is traveling on pavement at sea level. The engine produces a hefty 620 ft-lb of torqueand is in a gear of the transmission that provides a gear reduction of 5 to 1 with a 22 in wheelradius and 95% drivetrain mechanical efficiency. If the limo driver needs to accelerate hard inthe Ghost to avoid an accident, what would the acceleration be since it is a rear-wheel drive car?
Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm in 3 seconds. Calculate the heat generated for each engagement if clutch starting torque is 10 in-lb. a. 50 Btu b. 50 Btu c. 30.50 Btu d. 51.50 Btu
;: . L The contact surfaces in a cone clutch have an ej'fective diameter of 7‘5 i semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque requiy, 5 e slipping of the clutch if an axial force applied is 180 N. This clutch is employed to connect an electric motor running um_'form!y at 1 000 Epm. with, el which is initially stationary. The flywheel has a mass of 13.5 kg and its radius of gyriy, is Calculate the time required for the flywheel to attain full speed and also the energy [y, in of the clutch.
A flywheel maximum speed is 240 rpm and decrease to 200 rpm during the punching stroke. Themean diameter of the rim is 100 cm. Weight of the rim is 500 N and the weight of the arms andhub is 10% of the weight of the rim. Compute the energy released by the flywheel.
The rams of a four-ram hydraulic steering gear are 225 mm in diameter, the rudder stock is 450 mm indiameter, and the distance from the center of the rudder stock to centerline of rams is 800 mm. Calculate thestress (in MPa) in the rudder stock at the instant the rudder is moving past in mid-position and the hydraulicpressure is 80 bar.
A three cylinder radial engine driven by a common crank has the cylinders spaced at120°. The stroke is 138 mm, length of the connecting rod is 252 mm andthe mass of the reciprocating parts per cylinder is 2.2 kg. Calculate the primary and thesecondary forces at crank shaft speed of 1500 rpm.
Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
If the input force to the compound lever is P = 30 lb, calculate the output force Q.
The surface of the pressure plate contacts the. a. transmission main shaft b. throwout bearing c. clutch disc d. flywheel
Find the true magnitude and direction of forces on the wheel and cable members at static equilibrium